Z SKI
Donating Member
Hey guys, I need to offload this stuff as I need some $$$ to finish the truck. Help me get rid of this stuff so I can finally get my truck done.
1. Stock Sy half shaft, end cut down to fit corvette wheels. 88K miles in good shape however it needs a new boot as it started leaking grease about a month before i started my rebuild. $25 plus shipping.
2. Stock throttle/cruise/TV cable upper intake bracket. I have two of them in very good shape. $15 each plus shipping. BOTH PENDING
3. Stock egr/map/coil bracket. In very good shape. $15 plus shipping.PENDING
4. Stock SyTy harmonic balancer, near new. Came on my new motor that was only run a little. $30 plus shipping. PENDING
5. Stock SyTy steering shaft. Seems to still be good. $5 plus shipping.
6. Typhoon Energy Suspension body to frame bushings (red). Summit sent me the wrong kit and since it took me 2.5 years to figure it out they wont take it back. $86 from summit. $70 plus shipping.
7. NOS Antenna base nuts (5 available). $8 shipped each.
8. NOS gauge cluster lens assembly, Perfect, not one scratch or mark. This is my last one (and the best) from the half dozen that I had before. It would be perfect for that super low mile truck or if you are doing a resto. $200 plus shipping.
19. Stock S10 13 gallon gas tank. Bought it from Mr King a little while back and was unable to fit my RPM double pumper set-up inside the opening so it has to go. It includes a new sender that has been modified for the double pumper setup. I may make a adapter set-up that will let you run a single pump, but as of now I'm pretty busy. If I get around to it the price will go up about $30. As it is now it would be perfect for a sump and external pump set-up. Great condition. $175 plus shipping.
10. Renz fab throttle cable bracket for a truck that is running a electric trans and no cruise control. $15 plus shipping.
11. Renz fab MSD box bracket. $20 plus shipping.
12. Used stock throttle body with all sensors and an aftermarket air-foil. $60 plus shipping.
That's all for now. Please call all dibs on here to be fair to other members.
I also am looking for the following stuff to finish my truck:
-RPM Syclone 3" Exhaust (No muffler).
-Aeromotive fuel pressure regulator (With gauge port).
-PTE front mount intercooler with 3" aluminum bends so I can make my own intercooler.
-PML cast aluminum 4L80e pan.
-B&M trans cooler with the built in fan and thermostat (The bigger one).
-Dual core (1" or 1.25" tubes) fabricated aluminum radiator (Griffen, Be Cool, Etc..)
-March billet pulleys for the crank, water pump, power steering, idler and alternator.
-Black turbo blanket for a PTE-72GTQ
-And $$$ to get my machine work finished, swain tech coating on my hot parts and Nolan to tune my truck.
Thanks,
1. Stock Sy half shaft, end cut down to fit corvette wheels. 88K miles in good shape however it needs a new boot as it started leaking grease about a month before i started my rebuild. $25 plus shipping.
2. Stock throttle/cruise/TV cable upper intake bracket. I have two of them in very good shape. $15 each plus shipping. BOTH PENDING
3. Stock egr/map/coil bracket. In very good shape. $15 plus shipping.PENDING
4. Stock SyTy harmonic balancer, near new. Came on my new motor that was only run a little. $30 plus shipping. PENDING
5. Stock SyTy steering shaft. Seems to still be good. $5 plus shipping.
6. Typhoon Energy Suspension body to frame bushings (red). Summit sent me the wrong kit and since it took me 2.5 years to figure it out they wont take it back. $86 from summit. $70 plus shipping.
7. NOS Antenna base nuts (5 available). $8 shipped each.
8. NOS gauge cluster lens assembly, Perfect, not one scratch or mark. This is my last one (and the best) from the half dozen that I had before. It would be perfect for that super low mile truck or if you are doing a resto. $200 plus shipping.
19. Stock S10 13 gallon gas tank. Bought it from Mr King a little while back and was unable to fit my RPM double pumper set-up inside the opening so it has to go. It includes a new sender that has been modified for the double pumper setup. I may make a adapter set-up that will let you run a single pump, but as of now I'm pretty busy. If I get around to it the price will go up about $30. As it is now it would be perfect for a sump and external pump set-up. Great condition. $175 plus shipping.
10. Renz fab throttle cable bracket for a truck that is running a electric trans and no cruise control. $15 plus shipping.
11. Renz fab MSD box bracket. $20 plus shipping.
12. Used stock throttle body with all sensors and an aftermarket air-foil. $60 plus shipping.
That's all for now. Please call all dibs on here to be fair to other members.
I also am looking for the following stuff to finish my truck:
-RPM Syclone 3" Exhaust (No muffler).
-Aeromotive fuel pressure regulator (With gauge port).
-PTE front mount intercooler with 3" aluminum bends so I can make my own intercooler.
-PML cast aluminum 4L80e pan.
-B&M trans cooler with the built in fan and thermostat (The bigger one).
-Dual core (1" or 1.25" tubes) fabricated aluminum radiator (Griffen, Be Cool, Etc..)
-March billet pulleys for the crank, water pump, power steering, idler and alternator.
-Black turbo blanket for a PTE-72GTQ
-And $$$ to get my machine work finished, swain tech coating on my hot parts and Nolan to tune my truck.
Thanks,
Last edited:
Sorry :banghead::idea: