Search results

  1. oCancerPatiento

    Shifter cable attachment stud

    Im looking for the stud that attaches to the shifter arm on the transmission. The shifter cable then attaches to that. Please let me know if you have one.
  2. oCancerPatiento

    WTB Tailpipe bracket

    Im looking for the rear tailpipe bracket that bolts to the frame. My truck is missing it and cant install my exhaust until I find one. Its number 10 in the photo and the red piece circled. Please let me know if you have one.
  3. oCancerPatiento

    Tailpipe Bracket

    Im looking for the rear tailpipe bracket that bolts to the frame. My truck is missing it and cant install my exhaust until I find one. Its number 10 in the photo and the red piece circled. Please let me know if you have one.
  4. oCancerPatiento

    RenzFab??

    Just wondering if RenzFab is making parts anymore or if he still has any? I am wanting to buy a set of his spark plug heat shields.
  5. oCancerPatiento

    Best rear main seal?

    Im about to replace the rear main seal on my truck and was wondering what people are liking for their trucks. PTFE, Viton, rubber? I read somewhere that the PTFE seals can wear a groove into your crank. Anyone have any info or opinions on this?
  6. oCancerPatiento

    Motor mounts not fitting

    I am finally working on my truck after a 8 year hiatus. I am test fitting my engine in the frame so I can tighten the motor mounts down. I bought these Baja brand mounts a few years ago and they aren't made anymore. I liked the design of them since they aren't solidly mounted but not rubber...
  7. oCancerPatiento

    Flexplate bolt part #?

    I went to remove the flexplate bolts on my spare engine and almost all of them wanted to strip the heads. I have never had that happen before. I want to replace them with some ARP bolts but cannot find the correct ones. The closest I can find are for a 1 piece main seal with a flywheel but...
  8. oCancerPatiento

    WTB Driver Side Front Diff Axle Shaft

    I am in need of a front diff. drivers side short axle shaft. Mine is sheared off on the end. Please let me know what you have. Thanks.
  9. oCancerPatiento

    Frustrated installing torsion bars

    I am finally reinstall my suspension and torsion bars after a few years and dont quite remember how it was when I took it apart. Every where I read it says I need a puller to reinstall the torsion bars. When I go to install them it looks like there is two possibilities the "pork chop" will go...
  10. oCancerPatiento

    Pitman arm placement

    I bought a zq8 steering box awhile ago and am now getting around to installing it on the frame. I had a shop pull the pitman arm off the shaft to install the new power performance piece. I forgot to have them mark the direction of the old shaft so I don't know which direction to place the...
  11. oCancerPatiento

    WTB: Forged Pistons

    I am looking to buy a set of forged pistons. Please let me know what you have. Thanks.
  12. oCancerPatiento

    What pinion angle wedge should I get?

    I am installing belltech drop leafs and a 3/8" thick jtr setback plates with 1" jtr blocks. I would like to install new jtr pinion angle wedges inplace of the factory wedges. Does anyone know that angle I should get? They offer 2, 3, or 4 degree and I believe I read that factory was 8 degree...
  13. oCancerPatiento

    LS1 Brake Adapters

    I have a set of new ls1 brake adapters from Acehagg. They are powdercoated black. There are minimal scratches but have never been installed. Im looking to get $70 shipped for them.
  14. oCancerPatiento

    Where to buy fuel pump strainer?

    Im replacing the fuel pump assembly and when I took the the strainer off the walbro 255 pump the strainer came apart. Does anyone know where I can find just the strainer that fits this pump? Thanks.
  15. oCancerPatiento

    Body mount nut pictures?

    Just wondering if anyone has a picture of what the nut looks like inside of the body mounts. From what I can feel from my fingers it has a piece of metal welded to the nut to keep it from spinning inside the mount box. I think mine might be broken and dont want the piece rattling around inside...
  16. oCancerPatiento

    Shaft broken?!

    So I'm looking at my front diff cleaning it up and painting parts of it and when I pulled on the drivers side cv shaft flange it slid right out. To me it looks like the end that goes into the diff is sheered off but when I look into the diff it looks to be fine. It also slid out without any...
  17. oCancerPatiento

    Machine shop in MN?

    Im going to have my machine work on my block soon and was wondering if anyone in MN had any shops they like. Im looking at Northern Cylinder head in Andover or R&R Performance in Spring Lake Park. Im just doing a basic rebuild with forged pistons and eagle rods. Any info would be appreciated...
  18. oCancerPatiento

    Looking for eagle rods and forged pistons

    Im in need of a set of eagle rods and forged pistons. Im looking for used in good shape or new for a good price. Please let me know what you have. Thanks.
  19. oCancerPatiento

    Body mount bushing question

    I just ordered body mount kit # 3.4132 because it came up when I searched under Syclone. Well it turns out to be a kit for blazer/jimmy. When I contacted Energy Suspension they said it is the correct kit but it will just have extra bushings left over. Should I just return it and order kit #...
  20. oCancerPatiento

    Tailpipe pics

    I want to put different exhaust on my truck sooner or later. I was wondering if you could post pics of your Sy's rear ends so I can see the different tailpipe configurations. Please post what brands they are too if available. The rpm tailpipe looks like it is a turn down. I thought a ty...
Top