Typhoon II #735...Cage Assembly...New Pics!!

Windedv6

Ty n 10s
Re: Typhoon II #735...Cage Assembly...New Pics!!

MikeRenz said:
what alternator bracket/crank pulley setup is that? can you take a brighter pic of that side of the motor for me if you get a chance? I'm mounting my alt down there also, and am curious what premade kits are available. Thanks!

Mike

The alt kit is from March Pulleys...

Low Mount Alternator Kit

The information says it is 12.5 inches from the crank center to the outside of alternator. Mine came out at 11.5 inches. The crank pulley was machined to fit the balancer and the Peterson Spline Drive. The crank spline drive from Peterson was also tweeked to make everything work correctly.

DPNZO-HOJLK-PetersonDrive.jpg


Peterson Spline Drive Parts

I will get some closeup pics for you. Just beware that it is not a easy project to make it fit. Also I am not using a stock frame (you already know that, though). I have no idea if this setup works on a stock frame. I am also runing high mount twin turbos and am sure that these low mount setups will interfere with our stock location crossover pipes and power steering pump.

John
 
Last edited:

MikeRenz

not stock
Re: Typhoon II #735...Cage Assembly...New Pics!!

Windedv6 said:
I will get some closeup pics for you. Just beware that it is not a easy project to make it fit. Also I am not using a stock frame (you already know that, though). I have no idea if this setup works on a stock frame. I am also runing high mount twin turbos and am sure that these low mount setups will interfere with our stock location crossover pipes and power steering pump.
Great, thanks John! I'm not using a stock location xover pipe, and won't have a power steering pump at all (I still have to get another manual box since you stole mine :lol: ) . I just want my alt where the steering pump would be, so i'm confident the frame won't be in the way. I hadn't noticed the different sized pulley on the alt. I don't know if i feel like messing with drive ratio of the alt...I might just have a new crank pulley machined since i'm pretty sure the march setup isn't cheap. lookin forward to the closeup pic...thanks!

edit...just saw its only $150. Not too shabby. Only prob w/ it is that setup would hit my xover pipe. I'm planning on mounting the alt directly in front of the block, not out to the side of it like the march kit does. Still want to see some pics though :tup:
 

Windedv6

Ty n 10s
Re: Typhoon II #735...Cage Assembly...New Pics!!

Mike Renz said:
Great, thanks John! I'm not using a stock location xover pipe, and won't have a power steering pump at all (I still have to get another manual box since you stole mine :lol: ) . I just want my alt where the steering pump would be, so I'm confident the frame won't be in the way. I hadn't noticed the different sized pulley on the alt. I don't know if i feel like messing with drive ratio of the alt...I might just have a new crank pulley machined since I'm pretty sure the march setup isn't cheap. looking forward to the closeup pic...thanks!

edit...just saw its only $150. Not too shabby. Only prob w/ it is that setup would hit my xover pipe. I'm planning on mounting the alt directly in front of the block, not out to the side of it like the march kit does. Still want to see some pics though :tup:

The alternator crank pulley is 7 inch. The pic you see may be deceiving as the balancer is a 7.25 inch aluminum ATI balancer. The pulley on the alternator is one size larger than stock to give me the speed I wanted for the alternator. This alternator will run faster than stock and at an idle should put out a full 14 volts. I am a believer that keeping a steady voltage is a must with electronics (goes back to my car audio career, I guess). EFI, fuel pump computer, etc. should all run consistent. Also low voltage is the death of fuel and water pumps (as well as audio amps).

I will grab some better pics tomorrow if possible.

John
 

too many toys

IM LOVIN IT
Re: Typhoon II #735...Cage Assembly...New Pics!!

certifies to 7.50 you might want to chech the new rule book but if i am not mistake you need a funny car cage around the driver to be legal to 7.50 , 8.50 probably I would have some one check it before you go through the trouble of finishing everything and then have to go back and redo it .now that would piss a guy off.
 

Windedv6

Ty n 10s
Re: Typhoon II #735...Cage Assembly...New Pics!!

MikeRenz said:
Great, thanks John! I'm not using a stock location xover pipe, and won't have a power steering pump at all (I still have to get another manual box since you stole mine :lol: ) . I just want my alt where the steering pump would be, so i'm confident the frame won't be in the way. I hadn't noticed the different sized pulley on the alt. I don't know if i feel like messing with drive ratio of the alt...I might just have a new crank pulley machined since i'm pretty sure the march setup isn't cheap. lookin forward to the closeup pic...thanks!

edit...just saw its only $150. Not too shabby. Only prob w/ it is that setup would hit my xover pipe. I'm planning on mounting the alt directly in front of the block, not out to the side of it like the march kit does. Still want to see some pics though :tup:

Mike

Got back from business travel...took some pics of the crank drive.

CrankDrive1.JPG


CrankDrive2.JPG


CrankDrive3.JPG


CrankDrive4.JPG


CrankDrive5.JPG


CrankDrive6.JPG


Let me know if there is anything I can do to help...

John
 
Last edited:

MikeRenz

not stock
Re: Typhoon II #735...Cage Assembly...New Pics!!

pics are great. thanks a ton john! That'll def come in contact w/ my xover though. back to planning :tup:
 

Windedv6

Ty n 10s
Re: Typhoon II #735...Cage Assembly...New Pics!!

It is at the paint shop. The paint is finished, everything is back together. Just waiting for the window guy to get there and reinstall the glass. I will be picking it up this weekend. I now need to do the wiring, reinstalling the inner cooler, radiator, and a few misc items. The painter did a super job! Now I want to repaint my other one.

John
 

Windedv6

Ty n 10s
Re: Typhoon II #735...Cage Assembly...New Pics!!

It is getting there. The wiring is 90% finished. Paint is finished. It is at the interior shop getting custom seats, door panels, interior rear panels and carpet. The rest is nearly finished. A lot of little details to deal with...

I plan to have it at the Homecoming event. It won't be running, but will be fairly finished.

John
 
Top