Recent content by BillC

Cleaned up some old stuff, and ran across the spare upper and lower intake manifolds I had purchased many years ago. I have no idea what these are currently worth, but I paid $650 for the pair. The set came off a Sy, so the lower manifold is painted black from the factory. The manifolds are a...

Re: Laptop with Datamaster Sold!

Re: Laptop with Datamaster Bump. Don't be afraid to make an offer. I don't need this anymore, and so it needs to go....

Re: Eagle "H" beam rods Re: Eagle "H" beam rods No prob, happy to help. :)

Re: Eagle "H" beam rods Re: Eagle "H" beam rods Not much, just a fraction of an inch. The easiest way to clearance the pan is to: Put the engine on a stand, and roll it over so the crank is at the top. Place the pan on the engine WITHOUT any gasket. Rotate the crank, and feel where the rods...

Needham's EMP-11 chip burner. Includes power supply, parallel cable and software CD-ROM (everything that came with it from the factory). Datarase II EPROM eraser, with power supply and manual. 5) 27C2001 EPROMS, 3 have been used a few times, 2 are brand new. 1) 27C512 EPROM, used. Moates...

Hitachi laptop with licensed Datamaster software and cable. Also includes fairly new Li-Ion battery, 110v AC adapter, 12v DC car adapter, CD-ROM drive and 3.5" floppy disk drive. It's an older laptop, pentium MMX with Windows 95, but it runs well. There's a small crack in the left front...

Re: GN injectors in the TY?????????? As was posted earlier, check your fuel pressure regulator for a leaking diaphragm. Try pulling the vacuum line off the top of the regulator. If you see fuel in the line, or it smells like gas, the diaphragm is leaking and needs to be replaced -- a leaky...

Re: Needham Emp-10? I have an EMP-11, which I believe uses the same power supply as the EMP-10. My supply is rated at 12 VAC, 1000 mA. Yes, it says AC, not DC, which might make finding a replacement a little tricky. If you can't find one easily, you could try the manufacturer. My power...

Howdy, Promgrammer has been updated to v1.3, which fixes a couple of display bugs. I "shotgunned" it out to all registered users last night, but ended up getting about a dozen automated "user not found" error messages. If you did not get a copy, and believe you should have, please email me...

Re: Drivetrain swap vs. cab swap...opinions needed. Myclone -- I fully understand, and agree that there's a lot of emotional satisfaction in that approach, especially if you can get away with it. However, if you file a complaint with the police and press valid charges (which, in this case...

Re: Drivetrain swap vs. cab swap...opinions needed. That sounds like prima facie evidence that they were criminally invading your privacy (aka violating your reasonable expectation of privacy). Trespassing, too. Unless they had a search warrant and were duly designated Law Enforcement...

Re: Should I go for Vortec Heads? Your Opinions will really help! The stock exhaust manifolds will fit Vortec heads with no problem. However, you will need to have your intake manifold welded up and ported to fit the intake ports of those heads (the vortecs have a raised roof intake passage)...

Re: Becool Dual Core 62064 or 82064 That picture doesn't show the engine oil cooler that is in the left radiator tank of the stock radiator. That's probably why they said it wouldn't fit.

Re: Help with spark advance tables Jim, No big deal, don't worry about it. I just couldn't let a shot like that go by, without at least saying "Hey! WTF?!?". :) I believe Promgrammer shows the values correctly, at least as specified in the old documentation. However, since I've never...