also, help with abs

doomdead

New member
i dont think its the filters in the abs system, and i know all 4 sensors are pretty clean. when i reset the abs and drive past 15mph the lights dont come on, if i slam on my brakes, lets say in gravel, the abs works, but then throws the code again.... if i try resetting it right away as soon as i start driving the code fires up again. seems like if i wait awhile then reset them, they're ok until the next time i need to stop fast. anyone have an issue where -sometimes- they throw the code, and other times they dont?? ive never gotten them to work more than once, w/o throwing a code.
 

13.robb

New member
what code are you getting from the abs? i work for a dealer and can get alldata or techline info to help you get it fixed right.
 

doomdead

New member
just the abs and brake light come on, computer doesn't .... but while the lights are on the abs system is disabled, and ended up resulting in a high speed shit-in-your-pants 180 degree turn.
 

13.robb

New member
ive been there i experimented with my other truck a 2000 sonoma zr2 i pulled the fuse and went for a ride on the freeway at 90 when i hit the brakes, ive also seen a partially blown fuse cause a lot of probs not suggesting it but check it. theres got to be a code in that system. have you ever flushed your brake fluid either? sounds as if you are having some probs with the new ride, dont sweat it i rebuilt my stock motor aafter purchasing it and it went about 50 miles til the fuel pump or injectors went down knocking holes in 2 pistons. im replacing the whole fuel syst. too much work to r+r an eng again.
 

doomdead

New member
ill check the fuse but i know its not it.... and the fuild is in good condition, i spent the day bleeding the system again.. thanks for the help though... if theres a way to read the code let me know... like i said i dont get an engine check light.. just the abs and brake light
 

13.robb

New member
you will need someone that has a tech 1 or a snap on scanner etc. to access the abs module
you may have to take it to a shop to have it diagnosed but you can probably repair it yourself just get me a code and ill get the diag sheets to go from there.
 

doomdead

New member
I pulled a code 14 and 61... I didn't see 14 in the thing but 61: Code 41 through 66 4WAL control unit or motor circuit Check for a loose ground connection at the motor circuit. Clear the code and drive the vehicle. If any of these codes return, the EHCU valve may be faulty..... can anyone help me?
 

dgoodhue

BuSTeD 4.3
On 2002-03-27 00:07, doomdead wrote:
I pulled a code 14 and 61... I didn't see 14 in the thing but 61: can anyone help me?

Code 14 is normal, much like code 12 is normal for checking the ECU. I think code 61, basically means your ABS has sediment in it from not flushing the brakes. I flush the system and reset the code. You will eventually need a new/rebuilt ABS unit.
 

cattig

New member
I had the same problem with mine a year ago. I am pretty sure that the abs motor is shot due to dirt gumming it up. The actuators get stuck and this is why you can't reset it right away. If you wait awhile they sometimes free themselves up. If they don't you can tap on the abs motor with a hammer.

From what I understand the abs motors are sealed units and you can't rebuild them. A new one runs about $800.

I still haven't done anything with mine and a new problem has arisen. When the abs checks itself after you drive 20 feet, the actuators are sticking and the brakes are bypassing (pedal sinks to the floor). The same thing seems to fix it, a tap with a hammer. The new problem is worse then the first and I need to replace or remove the unit or risk crashing due to no brakes.

Good luck with your brakes.
 

mrweelr

New member
I had the same problem with my low-mileage Syclone. I tried everything and the fix ended up being just bleeding the brakes completely. I flushed the system twice with the bleeder screws completely removed and then filled it with Valvoline synthetic fluid. Haven't seen the brake or ABS lights come on since. You probably just have crud in your ABS unit. Do try this before spending any more time or money throwing parts at it!
 

V6 Kompressor

New member
GM had alot of problems with the motors, valves, wiring burning up ect. with these 4 wheel abs systems that were installed in the early 90 s-series trucks. I saw alot of complaints, tech. serv. bulletins and accident info on the NHTSB board. the web address is http://www.nhtsa.gov In about 10 to 20 years, we ought to see a recall from gm, after the lawyers get through with them...
 

doomdead

New member
I appreciate all your guys' help. I've bled the lines twice beliving i have had air left in them.... maybe its time to completely bleed it, ya know a few bottles.
 
Top