another boost controller thread...

Captain Morgan

Moderated User
ok, ive been searching the board, reading lots of replies and new ideas and basically what im running into is a money vs fuction issue.

ive been unemployed for a few months now, so cash is pretty tight. I finally got my PTE-52 installed on the truck. Runs and sounds great. Ive kept the stock chip in the truck mainly for the overboost security. Ive made a few short runs with Datamaster, the rod is way out of adjustment, but even with that and being in BAD need of tune-up, I've only seem a max of 9* knock and it was only once.

I want to put my ATR chip in, but my main concern is too much boost and no way to control it or stop it.

should I:

A: Turn the WG rod down enough so I simply can build that much boost to blow shit up.

B: Buy the $35 boostvalve.com deal which has been talked about alot on here (both good and bad)

C: Bite the bullet and get an electronic boost controller like the Ramchargers unit for $160.


Im not looking to break any records with the truck, but I dont wanna break the truck either.

Like I said, money is an issue and im more than willing to sacrafice performance for drivablilty.

I do have a 50# Ultimate here, but no injectors. Ill most likely end up selling this chip eventually.

Im actually planning on going with 36# Ford Blue Tops and a custom chip, but Im not exactly sure when that will be happening.
 

smeagol

Active member
PTE wastegate, when properly adjusted, should be 14-15psi. If you set it to less, you will have horrible spool up (basically you set the wastegate OPEN, leaking boost during spool).

The ATR & stock chip are set with too high a wastegate duty cycle to work properly with that setup. You'd probably see in the 20-25psi range with either (stock chip would cut out though).

The boost valve could work ok. The Ramchargers unit could work well also.

If you are doing a custom chip, you could dial it in then as well, starting out with duty cycle at 0%.

For now, if you are just starting to work on it and such, I'd set the boost to 15psi via rod adjustment, and unplug or bypass the wastegate solenoid.

FYI, if you set the wastegate rod on the PTE setup per *factory* specifications, you will have ~14psi (exhaust/intake setup will vary from truck to truck, one may see 13, another will see 15).

If you end up selling the chip, make sure you or the next owner get with me for the latest 50# calibrations to solve the problems that chip had.
 

Buster

New member
Whats worked best for us is to just unplug the electrical connector on the solenoid or run a straight hose from turbo to actuator as BG described. Rock solid boost control, turn wastegate rod for more or less boost. I wouldn't recommend using the boost valve, even know they work OK, you'll see spikes and unstable boost.
 

ed hess

race or get outta the way
morgan

You forgot to add selection no d

d. Get A Fuckin Job!

just kidding, btw bill and i will be at atco tonite!

2 trucks whose last runs were both 12.3.......this is going to bloody :D

ed
 

E-Rue

New member
morgan i agree with these guys. if you use only the hose thats included, and turn the rod end in just enough to have to pull it about 3/16" to get it latched inplace, as long as you are not running lean on top (and i suspect you are) you should get 13-14psi.

i wouldnt use the stock ECM controlled solenoid at all, unless your trying to dial in several different boost programs with the same rod adjustment (like the ultimate does).

i imagine your stock chip is a little lean on top.
that would be the next thing i addressed.
mabe you can try increasing your FP just a little.

e
 

Captain Morgan

Moderated User
ok, so screw the stock solenoid and just go from the barb on the top of the turbo to the barb on the wastegate.

also, Mike P offered me his ATR manual controller. Odds are Im gonna take him up on that. Would I still disconnect the stock solenoid? Jimmy is also gonna bring a boostvalve.com unit to the pittsburgh meet, so everyone can tell me what to do there also, im just trying to get things as close to ready as I can.

thanks again
 

Jimmy

Banned
NJTy180 said:
ok, so screw the stock solenoid and just go from the barb on the top of the turbo to the barb on the wastegate.

also, Mike P offered me his ATR manual controller. Odds are Im gonna take him up on that. Would I still disconnect the stock solenoid? Jimmy is also gonna bring a boostvalve.com unit to the pittsburgh meet, so everyone can tell me what to do there also, im just trying to get things as close to ready as I can.

thanks again
I guess you misunderstood me Morgan,I was saying that I'd bring my extra ATR controller.If you don't get with Mike before then,you will have mine at the meet for sure.

I'm gonna give the boostvalve.com controller back to the guy that gave it to me.I figure those things probably cost $25.
 

Captain Morgan

Moderated User
Jimmy said:
I guess you misunderstood me Morgan,I was saying that I'd bring my extra ATR controller.If you don't get with Mike before then,you will have mine at the meet for sure.

I'm gonna give the boostvalve.com controller back to the guy that gave it to me.I figure those things probably cost $25.

yeah, i guess I did. there really isnt any reason for 2 ATRs really. my badd. :D

the boostvalve ones are $35
 
morgan, if u want the ramchargers unit i am midst of setting up a dealer account and i can cut ya a break on my inital buy in order.
i am sticking one on my sy to try - i believe it will only be exactly precisely what i want, but life is nothing but shattered hopes anyway...
adam seems p[leased with his.
i can give you (and anyone else who wants one) a good deal - $140 - i have 3 or 4 left outta the buy in order remaining.
if u r interested, just lemme know.
mike
 

AXXE

Member
Adjusting the WG rod gives solid boost control. I don't even know if it is worth putting the ATR manual on it.
ED - How bloody was it? What did you run?
 

ed hess

race or get outta the way
well
they oiled the track 3 times that nite, really!

my 1st run was at 10psi and i ran a 12.3, 1.7460ft.

this was using the same setting on the ultimate as i did on the last 12.3

Now whats cool about it was the consistancy. I was within .006 on both 12.3 runs!

As for wheel spin. I had some wheel hop again after dialing it out with the adjustable shocks on the oem wheels and tires.

So i need to adjust them down a notch and test again. Caltracs may be in order here soon.

The 2nd run i did at a 5 psi launch and i now know that i wont run as well if i do this. Haveing never run that low at launch before it was a test .
ran 12.8 at 1.8x.

Did i learn anyting is alli hope to accomplish doing this tuning process and i did learn something. As for not breaking the 11.99 barrier. It will come. I have never gotten my best run on any visit on the 1st run.
Just matching my best was enough given the way the nite went with breakdowns.

Now speaking of breadowns. i didnt actually get to watch bill as i was ahead of him in the lanes. But i think his problems started when i got behind him to get fuel. He looked initimadated by the big fat tires on the shiny chrome zr1 rims i put on before i went to the track. :D

so anyway the story i heard was,
bill had put a bag of ice on his motor and the melted water got into the conectors or cap or something, or the 02 sensor wasnt working or ? but he never found the cause of why he was breaking up real bad.
Now i'm not saying or implying anything like he said all this for a credible excuse or anything but lets just say there wasnt any blood, and we all had a good time despite the frustration that bill had.

So how did that sound as a nice way to break bill's stones? :D

ed
 

AXXE

Member
You have the goods to go 11s now do it already. Did you stop using the DFI? If so, why? What speeds are you running? Are you running pump gas?
 

ed hess

race or get outta the way
only reason i thinki havent is i didnt have a boost controller to run higher than the 15 psi spring the pte 60 comes with. that ends tomorrow when the controler gets here. So far i have been just trying to get the spin out of the rear.

I am using a fuel cell now with 104 or 110.

maybe next tuesday!

ed
 

AXXE

Member
Why don't you adjust the WG rod for higher boost? The PTE set up is supposed to give solid boost control until about 22lbs. What controller will you be using?
 

ed hess

race or get outta the way
innovative controller. it'll be here tomorrow and on by next tuesday nite....
at least thats the plan. This is the new innovative unit with 17 settings on it. The old unit had 5.

Only question that remains is in another thread for how to use the controller to launch....

ed

anybody have a 2-7 lb spring for an actuator to fit a pte60?
 
Top