Ideas?

Richie Rich

Richie Rich

New member
Re: Ideas?

leroy said:
Rich,

I think you need a "noid" light to test the injector pulses.

Let me know if you need help. I'm not too far away.

Jim
Click to expand...

Thanks Jim. The Ty is in Rolla Mo right now. I will be down there this weekend to check it out some more. I will pick up a NOID and check that out also.
 
Richie Rich

Richie Rich

New member
Re: Ideas?

Ok. The injectors have power. The motor will still just crank and not run. I'm sure the EGR is good. All fuses are good. Any ideas
 
chelo

chelo

filthy sy
Re: Ideas?

ignition module?
Click to expand...
That's my guess too. When i first installed my engine, it only idled for about 2 minutes and then it died. Might aswell buy a new one if you haven't yet.
 
leroy

leroy

Donating Member
Re: Ideas?

Are you sure the distributor is in right?

I think I have a replacement ecm with injector driver upgrades, if you need a substitution test.

Jim
 
Richie Rich

Richie Rich

New member
Re: Ideas?

leroy said:
Are you sure the distributor is in right?

I think I have a replacement ecm with injector driver upgrades, if you need a substitution test.

Jim
Click to expand...

I would love to test with your ecm. How soon do you need it back? I can only make it to Rolla on weekends. I can pick it up in Lawrence from you sometime if that is ok with you or we can meet in KC area sometime. I appreciate your help.
 
leroy

leroy

Donating Member
Re: Ideas?

I checked this morning and have 2 spares. One has a bad fuel pump relay driver (could be used with the relay test wire hot-wired). The other one has a question mark on it, so not sure what was going on with it. I'll put together a couple more this afternoon.

If you want to come by, that would be convenient for me. I'll be around most of this week.

Jim
 
Richie Rich

Richie Rich

New member
Re: Ideas?

leroy said:
I checked this morning and have 2 spares. One has a bad fuel pump relay driver (could be used with the relay test wire hot-wired). The other one has a question mark on it, so not sure what was going on with it. I'll put together a couple more this afternoon.

If you want to come by, that would be convenient for me. I'll be around most of this week.

Jim
Click to expand...

Great. I will be leaving out of Rolla this afternoon. So maybe Wednesday would work for me how bout you? Also if you have a known good ECM with the inj drivers upgrade already done I will buy it from you. Or could trade you some parts.

Rich
 
Richie Rich

Richie Rich

New member
Re: Ideas?

Special Thank you to Jim Sloan. He got my Ty going this weekend. Thanks Jim for taking time out of your schedule to help out a fellow SyTy'r.
 
W

wantingasy

Active member
Re: Ideas?

Dang, you waited almost 8 months and now it's finally going. I don't think I could last that long...lol...What ended up being the problem?
 
Richie Rich

Richie Rich

New member
Re: Ideas?

My Phil Long chip was the main prob believe it or not. Jim did a trial burn on a chip for me and it fired up. Jim helped me clean up my vac lines and did some heat shielding. He also fixed a rocker arm that was ticking. That was another thing I would have never expected. Right now it runs real rich. Waiting on Phil to send me a good chip. If I can get it by this weekend then I will go down and drive it back. Have it at the Nats (Hopefully). Jim is a real stand up guy. He knows these trucks that’s for sure. It was killing me that I have not drove this truck since Aug 2004.
 
Richie Rich

Richie Rich

New member
Re: Ideas?

Here is what Jerry McCoy says it is. http://www.tobefast.com/detail.aspx?ID=384

McCoy Motorsport Sy/Ty Super Motor SyTy_SuperMotor Enough to get you into the 10's 1/4 Mile.... We start with a selected block. Then Machine it for 4-bolt splaid caps, put in TRW Pistons your choice of cam depending on engine management used, Eagle rods, Crank Shot penned and Nitrated, Total seal rings, Then we top it off with our famous stage two Vortec Heads. These Babies flow the Big Numbers for power on top with out sacrificing drivability and low end power. Everything is balanced, blueprinted and race prepped with secrets learned over the years. We also Port-Polish and Refinish your Sy / Ty Intakes as part of this package. When ordering select whether or not you'll be sending us your block for a core (other a $400.00 dollar core charge will apply). Allow 8-9 weeks for engine completion. We will contact you upon ordering to setup shipping method (shipping will be a separate charge depending on your location).
 
You must log in or register to reply here.
Top