Overboost or Detonation (or both)?

dgoodhue

BuSTeD 4.3
Re: Overboost or Detonation (or both)?

you could take the vacuum hose straight off of the turbo and put it directly onto the wastegate solenoid. This will open the gate up right off the bat, and give you the least amount of boost that the turbo can make. This will at least let you know if its the solenoid, or if you have some other problem. I would only recommend this after you make sure that the gate is not frozen, and that the actuator does not leak vacuum.

Good advice. Does original poster have scan tool? I am not quite sure how he is accurating diagnosing overboost with stock gauge or detonation with out it?
 

SyTyAddict

Member
Re: Overboost or Detonation (or both)?

http://www.syty.net/forums/showthread.php?t=80764

I don't like the sound of your goofy chip, just for giggles, you could take the vacuum hose straight off of the turbo and put it directly onto the wastegate solenoid. This will open the gate up right off the bat, and give you the least amount of boost that the turbo can make. This will at least let you know if its the solenoid, or if you have some other problem. I would only recommend this after you make sure that the gate is not frozen, and that the actuator does not leak vacuum.

What I was thinking, but the early bird beat me to it. With the hose directly on the wastegate from the port on the turbo, it should only make 5-8 psi. Do you still have the stock chip? If so, then I would put it in. Is the truck still running a cat, if not it can cause boost spikes and overboost.
 

turbodig

Active member
Re: Overboost or Detonation (or both)?

Good advice. Does original poster have scan tool? I am not quite sure how he is accurating diagnosing overboost with stock gauge or detonation with out it?

x3.

I'd start by pulling the passenger fenderwell and checking the WG flapper for free movement while the turbo is hot.

With the hose directly to the canister, you should make minimum boost.

Hopefully it hasn't damaged anything yet.

Another board member recently bought a restaurant in Cavalier, which is a bit closer to you.
Maybe we can have a meet-up there sometime?
 

MAK

New member
Re: Overboost or Detonation (or both)?

I would like to replace the chip with a stock one but it is nowhere to be found and the truck has the original exhaust (w/cat, of course). I will try thr turbo to wastegate test and also check the wastegate rod for movement when it is hot. It does move a little when cold. I don't have a scan tool, as of yet, but the mechanic was going to do all of that. Now the last few times I have talked to him he keeps pushing back the timeframe to work on it. Here we go again......same thing in NC.

Turbodig - it would be great to meet up some time. Let me know when and I will work on it.
 

MAK

New member
Re: Overboost or Detonation (or both)?

DGOODHUE - I just re-read you post. I have not been able to do anything with the truck in the last week due to a lot of overtime at work. I do have the stock gauges but before the new stock turbo was installed last year there was never a problem of the boost going high on the gauge. And the fact that it is making a loud noise after a hard acceleration now but did not before tells me something is not right. I am sure it could be figured out with a scan tool. I was asking the question because I am worried about damaging the engine before the mechanic can look at it. I am taking it easy on the truck and will try the last few tips with the hoses tomorrow when I am off work.
 

MAK

New member
Re: Overboost or Detonation (or both)?

I connected the hose from the turbo directly to the waste gate and no overboost and no loud noises. Would this indicate a bad solenoid or do I have other issues? I am surprised there is nothing like this already posted elsewhere. Surely, even with my luck, someone else has had this problem. Oh, what fun.......
 

bundie

New member
Re: Overboost or Detonation (or both)?

Mine ty is also overboosting.

Some trucks get that problem with a difrent exhaust with better flowing mufflers.

Get datamaster connected and you know what the real problem is.
Cheap solution what i have.install a bov with a 1bar spring
 

turbodig

Active member
Re: Overboost or Detonation (or both)?

I connected the hose from the turbo directly to the waste gate and no overboost and no loud noises. Would this indicate a bad solenoid or do I have other issues? I am surprised there is nothing like this already posted elsewhere. Surely, even with my luck, someone else has had this problem. Oh, what fun.......

Possibly a bad solenoid, but more than likely an adjustment issue.

Pull the passenger side wheel and inner fender. Adjust the WG rod such that there's barely enough tension on the rod to hold the flapper shut. Put the wheel back on and re-test. If you get an overboost condition again, It's likely the WG solenoid or the related plumbing. It could also be an issue with whatever chip is in there.

If it doesn't have issues, your solenoid and plumbing are good. Tighten the rod 1/2 turn at a time until you reach normal (14.5-ish) max boost. The stock gauge isn't accurate enough to dial this in properly, it needs to be a good external. Even if it's an AutoZone or Harbor freight cheapie, it's better than the stocker.

Can you snap a pic of the following:

Your ECM with the chip window open
The hoses surrounding the WG solenoid and WG actuator canister.

A general engine compartment pic would be helpful as well, so we can see if there are any odd mods done that you might not recognize.
 

MAK

New member
Re: Overboost or Detonation (or both)?

Turbodig - I will check it out and get some pictures. Oh, and your PM inbox is full.......you must be very popular here.....:tup:
 

MAK

New member
Re: Overboost or Detonation (or both)?

Turbodig - I am trying to send you a PM but your inbox is full. I have something to ask you about......:D

I did check the waste gate. For some reason the overboost seems to have went away today and it did not make any loud noises. It does seem rather sluggish, though. I took the pictures but may need some help figuring out how to post pictures from my computer (not a website, ie: photobucket) Is this possible?
 

turbodig

Active member
Re: Overboost or Detonation (or both)?

Turbodig - I am trying to send you a PM but your inbox is full. I have something to ask you about......:D

I did check the waste gate. For some reason the overboost seems to have went away today and it did not make any loud noises. It does seem rather sluggish, though. I took the pictures but may need some help figuring out how to post pictures from my computer (not a website, ie: photobucket) Is this possible?

You can save the pics to photobucket and just copy and paste the URL in a message here.

A loose adjusted wastegate will be sluggish... that's normal.

My PMs are always full... I've long since given up.
Try my email -
turbodig <at> yahoo [dot] com
 

MAK

New member
Re: Overboost or Detonation (or both)?

Turbodig - I have not had time to create the photobucket account but should be able to tonight (hopefully). I will then post the pictures I took the other day.
 

MAK

New member
Re: Overboost or Detonation (or both)?

Turbodig - A few pictures, as requested (hopefully)

008.jpg

005.jpg

S3000012.jpg

S3000024.jpg

S3000018.jpg

S3000019.jpg

S3000020.jpg


It is very dirty, but hopefully you can see what you need clearly enough. Hopefully I will be getting a stock chip soon to replace the Hypertech.

If there is anything specific you want to see let me know.
 

Chest Rockwell

Active member
Re: Overboost or Detonation (or both)?

S3000024.jpg


It is very dirty, but hopefully you can see what you need clearly enough. Hopefully I will be getting a stock chip soon to replace the Hypertech.

If there is anything specific you want to see let me know.

You've got the stock chip (memcal) already. The brown bar, with a blue lid hanging off the side of your Hypertech setup is the stock memcal. Just seperate it from the Hypertech adapter, and put it back in the ECM.

Should look like what you've got:
1138117.jpg


Memcal with the cover off. Though not syty, our look similar.
memcal.jpg


What you want to see when you're done:
65d1169844289-mpfi-works-ecm.jpg
 

MAK

New member
Re: Overboost or Detonation (or both)?

You've got the stock chip (memcal) already. The brown bar, with a blue lid hanging off the side of your Hypertech setup is the stock memcal. Just seperate it from the Hypertech adapter, and put it back in the ECM.

Should look like what you've got:
1138117.jpg


Memcal with the cover off. Though not syty, our look similar.
memcal.jpg


What you want to see when you're done:
65d1169844289-mpfi-works-ecm.jpg

No wonder I could not find it. The thing was in there all along. I thought it was separate....I have a lot to learn. Thanks for clearing that up.
 

MAK

New member
Re: Overboost or Detonation (or both)?

Next question/suggestion solicitation.....:lol:

I have the RPM air intake. No performance enhancements. I was going to buy a new boost solenoid and harness. Should I buy a BOV instead? Are both required for proper performance and could the BOV also help (not solve) the issues with the boost? Symptoms (issues) were described earlier in this thread. I could not find a definitive answer to this one.

Any thoughts?

Thanks, once again.
 

turbodig

Active member
Re: Overboost or Detonation (or both)?

Next question/suggestion solicitation.....:lol:

I have the RPM air intake. No performance enhancements. I was going to buy a new boost solenoid and harness. Should I buy a BOV instead? Are both required for proper performance and could the BOV also help (not solve) the issues with the boost? Symptoms (issues) were described earlier in this thread. I could not find a definitive answer to this one.

Any thoughts?

Thanks, once again.

A BOV isn't going to resolve a boost problem, and it's one of the last things I'd put on a stock truck.

You do need one of these, and gauges to put in it. Boost and Trans Temp would be a good start.
http://www.gaugepods.com/gmc.html
 

MAK

New member
Re: Overboost or Detonation (or both)?

A BOV isn't going to resolve a boost problem, and it's one of the last things I'd put on a stock truck.

You do need one of these, and gauges to put in it. Boost and Trans Temp would be a good start.
http://www.gaugepods.com/gmc.html

The BOV was suggested because of the loud mystery noise that was occurring after acceleration. I still do not know what was causing that one.

Gauges are on my list. My oil pressure gauge stopped working so I will need one of those, as well.
 
Top