Throttle body linkage swap

canadian

sy in progress
How easy is it to swap throttle body linkages between throttle bodies? I have a stock SyTy throttle body and an aftermarket one that I need to put the linkage on.

The aftermarket one has the linkage held on with a bolt, but the SyTy is attached to the throttle shaft and then the shaft is pressed so that it won't come off. I know I'll have to cut it off, but will the spring thing-a-majig come unwound when I take it off?

Never done this before, so I'm looking for some confidence inspiration here.

Thanks
 

warmpancakes

New member
Re: Throttle body linkage swap

does the aftermarket have any bracket? The sy/ty only piece bolts on just need to remove the studs of other tb and bolt sy/ty piece on
 

canadian

sy in progress
Re: Throttle body linkage swap

Here's the current bracket setup

$%28KGrHqFHJCME+Z+Jm7LVBQRhRoWyLw~~60_57.JPG
 

canadian

sy in progress
Re: Throttle body linkage swap

Yeah, it was a decent deal that I couldn't pass up. Typical of me I buy before I do my research and it usually bites me in the ass. I don't have cruise so the only thing I need to attach are the throttle cable and transmission cable, although I do know that the transmission cable adjustment is the most important thing of all.

If I can't use the stock bracket I may be able to remove the stock bracket and swap it over, but I don't know if it will work or not. I have a few spare TB's sitting around that I'm going to look at.
 

warmpancakes

New member
Re: Throttle body linkage swap

Lingenfelter and accel use that same TB perhaps one of them can sell you the correct linkage?
 

nallj92

Active member
Re: Throttle body linkage swap

Get the TPI inner bracket, and bolt on the syty outer bracket. I'm running a Professional Products 58MM for TPI motors and took out the bottom linkage pin and bolted the syty outer on it.
 

canadian

sy in progress
Re: Throttle body linkage swap

Get the TPI inner bracket, and bolt on the syty outer bracket. I'm running a Professional Products 58MM for TPI motors and took out the bottom linkage pin and bolted the syty outer on it.

The issue is finding a TPI inner bracket. From what I can tell Lingenfelter doesn't sell these any more. I've emailed Accel and no response. I'm going to try swaping the whole assembly from a spare SyTy TB I have. I won't know if anything works until I get it off the old TB and compare how they are both mounted.
 

nallj92

Active member
Re: Throttle body linkage swap

stock is pressed in right? grind, pop it out the notches may be the same to just bolt it on. I can take a pic of what I have on my bolt on style stuff if you need.
 

canadian

sy in progress
Re: Throttle body linkage swap

stock is pressed in right? grind, pop it out the notches may be the same to just bolt it on. I can take a pic of what I have on my bolt on style stuff if you need.

That's what I plan on doing. If you could post pics of your stuff that would be appreciated.
 

canadian

sy in progress
Re: Throttle body linkage swap

Last night I drilled out the swaged end on an old throttle body and did a little grinding to get the linkage off. Tested the swap on to the new TB. It seems to work.

IMAG0218.jpg
 

canadian

sy in progress

Throws

Active member
Re: Throttle body linkage swap

So... how are you adapting it to your upper? I'm trying to see how others have adapted large bores to the stock upper.
 

canadian

sy in progress
Re: Throttle body linkage swap

The upper would need to be machined so that the holes are 58mm as well.
 

canadian

sy in progress
Re: Throttle body linkage swap

No porting has been done yet. I probably could do it myself with a dremel. Shouldn't be too hard.
 

Gnocide

turbo game burt reynolds
Re: Throttle body linkage swap

Get the TPI inner bracket, and bolt on the syty outer bracket. I'm running a Professional Products 58MM for TPI motors and took out the bottom linkage pin and bolted the syty outer on it.

you running cruise control? got pics please??
im wanting to use the complete factory linkage and go with a simple 52 mm
( some good advise from a 10 sec Ty member i think is golden.)
 
Last edited:
Top