Torision Bar Removal

0966Sy

Code what?
Is there a trick to remove the torision bar crossmember and bars without cutting the bars? this job looks easy but has become to be a pain in the ass.

Erik
 

Loeryder

New member
There is a torsion bar "Unloader" tool.
It is under pressure even with the suspension in full droop.
You have to get the pressure off to get the porkchop keys out.
Back the adjusters out until the bolts come out and try twisting on the tbar.
Also you can use a tap hammer (towards the front of the truck) to give it a push out of the control arm.
Be very careful because it is under pressure and depending how it does dislodge itself it has some sprung weight behind it.
Then you should be able to drop the porkchop keys.

torsionbars.jpg

AutoZone has a free loan a tool pogram and I think they offer the unloader tool up at no charge.
Give a deposit and you get it back when you return it.
www.autozone.com look under loan a tool the store location to find the nearest one...

You puttin in coilovers?
Fun stuff.
 

Ian Turgeon

Cascading Inspiration
we were able to pull them w/o a tool durring a bushing install. pulled the adjustment bolt out, and was pulling on the lower a -arm and the porkchop fell out because the tbar was coming with it.

so its posible you may not need the tool, just be carefull
 

0966Sy

Code what?
The Q's:
Thanks for the input guy's, their are a few things im not sure of. What is the "porkchop". And im i trying to remove the bars from the torision bar or the A-arms or both? And is there anything else i need to know to do when detaching them from either the A-arm or the trorision bar. I'd like to do it as simple as possible because i will be reinstalling them when im done with replacing the frame crossmember that sits in front of the torision bar.


The story behind the damage: :x
It got all bent up by getting cought on the extended hitch mount on my trailor, thus it is going to make it almost impossible to pull the trans to put in the new 9/11. the damn thing would be to expensive to even attemp to get it streightend at a body shop and it still would not be perfect so im just going to see if they can order me a new one, to replace.


Damn i wish i was rich :D
I was thinking to just go coil over's to save the trouble of putting the torision system back in and getting one of those fancy chromemolly ones from Al but i cant spend that kinda money now, and if i do go coil over's i'd like to get the rear's as well :(

Thank you guy's (your helping me save money)
Erik
 

Loeryder

New member
The "porkchop" key is the torsion bar adjuster.
It is shaped kinda like a porkchop so we call it so.

Thats your first goal get the adjuster off,
The Tbar will stay lodged in the control arm unless you force it out.
Not sure how far down you want to tear into it...
 

peterpaw

New member
make your own tool

make your own tool

hi there,

it is easy to make your own tool.

buy a good american quality, preferably forged 6" or 8" "C" clamp. take the flat swivel off the screw part and the ball that remains fits perfectly in the indentation of the "pork chop" as it is being refered to here.


JACK UP THE TRUCK and put jack stands under the chassis (not the A arms)
1. use your newly made tool by tightening the ball of the screw part of the clamp into the indentation in the pork chop. (use a light and you can see the spot to put the ball end into)to hold the adjuster in place and take the pressure when you release the pressure with the adjuster bolt.
2.remove the bolt that is used for adjusting ride height
3. remove the small part that the adjuster screw threaded through
4. remove your new tool by letting the pressure of the "pork chop" it will hang down slightly
5. grab the torsion bar and try to pull it towards the rear. if it doesn’t come right away go to the front of the truck and you can see the front of the torsion bar when you look at the lower A frame. use something heavy like a junk axle shaft or a 1" rod and hit the torsion bar towards the rear.
6. at some point the pork chop will come off.
7. you now have the bar loose; you may have to take apart the parts that the cross member hangs from (at least on one side of the truck. i don’t remember which side.)
8 now repeat this on the other side of the truck.
9. by this time you are an old hand at removing the torsion bar and the second one is a piece of cake.

Make sure you remove the swivel on the C clamp, if you dont you will ruin the clamp and will have to buy a second clamp that this time you sensibly will remove the swivel from. this comes from a man who had to buy two clamps.

the end of the bar in the A frame may have some surface rust, clean that off and the bar goes back in easy as pie and don’t worry about the loose fit. it was made that way.

this is easier than rear springs

good luck

p.s. my ZR now sits on 26" wheels with syclone bars about 9” lower
 

0966Sy

Code what?
Thank you so much Pete, that couldnt have been anymore straight foward. That saved me some money at the body shop. The new crossmember is only going to cost me $60.

Erik
 
Top