Sean Krupa
Moderator
Re: Typhoon #1215 Mods
Flex a Lite 31163.
Flex a Lite 31163.
Typhoon #1215 Mods
- Thread starter Sean Krupa
- Start date
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
The controller is Progressive so the fans will slowly ramp up and doesn't spike the system.
The controller is Progressive so the fans will slowly ramp up and doesn't spike the system.
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
Removed the A/C Compressor and Bracket. Next will be the Turbo to get ready to Sell.
Removed the A/C Compressor and Bracket. Next will be the Turbo to get ready to Sell.
graham1524
Well-known member
Re: Typhoon #1215 Mods
Looking to sell those stock AC lines?
Removed the A/C Compressor and Bracket. Next will be the Turbo to get ready to Sell.
Looking to sell those stock AC lines?
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
Planning on keeping everything.
Planning on keeping everything.
Slyclone
Well-known member
Re: Typhoon #1215 Mods
Shoot me a pm with info on turbo if /when you decide to sell. Might be interested.
Removed the A/C Compressor and Bracket. Next will be the Turbo to get ready to Sell.
Shoot me a pm with info on turbo if /when you decide to sell. Might be interested.
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
Recieved my Precision 72GTQ Turbo today. Also got a chance to remove my PTE63. Will be getting the exhaust side Ceramic coated and ofcourse the Compressor side Polished. The PTE63 is for SALE
Recieved my Precision 72GTQ Turbo today. Also got a chance to remove my PTE63. Will be getting the exhaust side Ceramic coated and ofcourse the Compressor side Polished. The PTE63 is for SALE
choffert1
New member
Re: Typhoon #1215 Mods
Hi Sean I have a question in the third pic what oil return flange is that? I have been looking for one just like it and cannot find one. It would work perfect for me my drain is just a hair to short from my new turbo setup.
Finally finished Polishing my Turbo. Next is taking the Exhaust housing off to get Ceramic Coated black. I also painted the center section with some 2000* header paint.
BEFORE
AFTER
Hi Sean I have a question in the third pic what oil return flange is that? I have been looking for one just like it and cannot find one. It would work perfect for me my drain is just a hair to short from my new turbo setup.
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
To be honest not sure. It came on the Turbo when I bought it. I would imagine they have flange extensions on Ebay or something. Sorry.
To be honest not sure. It came on the Turbo when I bought it. I would imagine they have flange extensions on Ebay or something. Sorry.
dgoodhue
BuSTeD 4.3
Re: Typhoon #1215 Mods
My PTE turbo came with that extension. I would contact PTE directly for the extension.
My PTE turbo came with that extension. I would contact PTE directly for the extension.
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
Hey Adam, I bought it New from a board member. Older version 72GTQ.
Trying to sell my PTE63
Hey Adam, I bought it New from a board member. Older version 72GTQ.
Trying to sell my PTE63
choffert1
New member
scottyblazinlow
Red tyclone
Re: Typhoon #1215 Mods
Did you Polish the turbo by hand?
Did you Polish the turbo by hand?
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
I sanded the casting marks with a drill and sanding drums, then I wet sanded it followed by polishing compound on my bench polisher.
I sanded the casting marks with a drill and sanding drums, then I wet sanded it followed by polishing compound on my bench polisher.
Slyclone
Well-known member
Re: Typhoon #1215 Mods
Hey Sean,
I browsed back a few pages.. (16,17) I was looking for a idea on how you finished off the coil/ map sensor bracket and the other rounder one attached to it .
Only asking because I know you have similar if not the same tall alum. Valve covers. I don't think the bracket fits well and I remember a thread with a spacer of some sort. My idea was to try to extend the harness and vac hoses and relocate them else where. Just wondering how you finished it off.. Or if you used the spacer and how it fits.
Hey Sean,
I browsed back a few pages.. (16,17) I was looking for a idea on how you finished off the coil/ map sensor bracket and the other rounder one attached to it .
Only asking because I know you have similar if not the same tall alum. Valve covers. I don't think the bracket fits well and I remember a thread with a spacer of some sort. My idea was to try to extend the harness and vac hoses and relocate them else where. Just wondering how you finished it off.. Or if you used the spacer and how it fits.
Sean Krupa
Moderator
Re: Typhoon #1215 Mods
I'll snap a pic for you of what I did. I used some spacers that I believe are for sway bar links that I had laying around which spaced the Map/Coil bracket up perfectly.
Removed the rest of the A/C parts and next is getting the Heater box out. Had to remove the Valve cover for clearance to get the box out.
I'll snap a pic for you of what I did. I used some spacers that I believe are for sway bar links that I had laying around which spaced the Map/Coil bracket up perfectly.
Removed the rest of the A/C parts and next is getting the Heater box out. Had to remove the Valve cover for clearance to get the box out.
ZavzTy547
Senior Member
Re: Typhoon #1215 Mods
Sean, why not leave the A/C on the truck? Be very cool to see a 10 sec pass with stock bottom end with A/C. . .
I'll snap a pic for you of what I did. I used some spacers that I believe are for sway bar links that I had laying around which spaced the Map/Coil bracket up perfectly.
Removed the rest of the A/C parts and next is getting the Heater box out. Had to remove the Valve cover for clearance to get the box out.
Sean, why not leave the A/C on the truck? Be very cool to see a 10 sec pass with stock bottom end with A/C. . .