Search results

  1. S

    ultimate chip user's,knock light flickers intermittently

    Re: ultimate chip user's,knock light flickers intermittently I just got done driving the truck with a tech 1 attached using datalist.The results were yess it's showing knock on the scan tool. At between 6-7 lbs. of boost it showed 2-5 degrees of knock.the scan tool showed me basic info also...
  2. S

    ultimate chip user's,knock light flickers intermittently

    Re: ultimate chip user's,knock light flickers intermittently Hey Dig, What would cause detonation at this low of a boost level/timing. I run good quality fuel, 93.The truck has new ur5 plugs, taylor wires, fuel filter, pcv valves, cap/rotor, operating new johnson intercooler pump, etc.I have...
  3. S

    ultimate chip user's,knock light flickers intermittently

    hey guys. I just got my Ultimate chip installed in my truck and on moderate acceleration,8-10 psi boost, my knock light will flicker and go out, esp. during gear changes.possible false knock like I've seen on many GN's ? Anyone with experience with this chip for stock truck with cold air and...
  4. S

    Crankcase Vapor Burn Off

    Re: Crankcase Vapor Burn Off I ordered new pcv valves from GM parts dirrect, 799c also ordered a drivers side screw in breather and the moroso crankcase evacuation kit 25900. There is no smoke coming from the tailpipes during start up or while idling and when I replaced the spark plugs they all...
  5. S

    Crankcase Vapor Burn Off

    Re: Crankcase Vapor Burn Off cavscout, that is the system i'm talking about.Anyone know where a good place to weld the venturi tube in.How many inches in front of the cat. conv,?
  6. S

    Crankcase Vapor Burn Off

    Re: Crankcase Vapor Burn Off sounds like there are alot of bad motors out there with the number of pcv valve posts for vapor issues.
  7. S

    Crankcase Vapor Burn Off

    I was going to install a weld in barb fitting to burn off oil vapors coming through dash from drivers side valve cover vent. Question is ,do I need to put some kind of check valve in the vapor line to keep exhaust from pushing up the vapor tube back into the engine? Thanks
  8. S

    Anyone have any issues with noisy frame to body bushings

    Re: Anyone have any issues with noisy frame to body bushings Sorry, it's the one under the driver's door. Thanks
  9. S

    Anyone have any issues with noisy frame to body bushings

    Hey guys another annoying noise I am hearing is the drivers side frame to body bushing making alot of noise on bumps. Any repairs for this?
  10. S

    Is There Two Different Part Numbers For The Pcv Valves

    Re: Is There Two Different Part Numbers For The Pcv Valves That's all good info. So the 799c is correct for both openings?
  11. S

    FlexLite Fan??

    Re: FlexLite Fan?? I know what your talking about. That is a great question. Much lighter ,less resistance turning and still draws alot of air through the radiator. Bump for good question.
  12. S

    Is There Two Different Part Numbers For The Pcv Valves

    I've done quite a few searches on pcv related topics. I read once that both pcv valves have the same part number.Then I read on another post that there are 2 different part numbers for the front valve and the back. Which is it? Thanks
  13. S

    Kenne Bell still sell sy/ty parts?

    Re: Kenne Bell still sell sy/ty parts? the long straight orange one between the 2 black plastic elbows. About 15-18" long. Thanks for the assist on the photo Pimp.
  14. S

    Kenne Bell still sell sy/ty parts?

    Re: Kenne Bell still sell sy/ty parts? Unfortunately I don't. But, it is the orange hose that goes from the elbow to the air filter on the KB cold air kit. It is spiral wound orange silicone. T hanks
  15. S

    Kenne Bell still sell sy/ty parts?

    Re: Kenne Bell still sell sy/ty parts? Any info on were I could get a replacement 3" silicone hose like the orange one in the k.b. kit that's about 18" long?
  16. S

    Kenne Bell still sell sy/ty parts?

    The car I just bought has some Kenne Bell cold air intake on it and I need a new silicone 3 " hose to the air filter.All I saw on his web sight is supercharger/C obra stuff. Thanks
  17. S

    Who's using alky and what kit?

    Re: Who's using alky and what kit? Thanks guys. I had Julio's kit on my TTA, worked well but was a pain to install. Thanks for the help.
  18. S

    Who's using alky and what kit?

    Hey guys , I'm a new member and 3 time former Buick owner. I wanted members opinions and typhoon experience with the different alky company's kits. Best install and most reliable. Thanks
Top