Search results

  1. T

    Question

    I have searched numerous threads...who is selling complete vacuum line replacement --silicone lines w/ all fittings/elbows et cetera.for our vehicles..? thanks
  2. T

    Headliner?

    Re: Headliner? LMC parts..I think they ABS plastic headliner too......
  3. T

    trouble at 2500 rpm

    Re: trouble at 2500 rpm Help!!!!!!!!!! TPS changed...No knock, just erratic stumbling....especially between 2000 and 3000rpm....I am 2hrs from Dallas in case someone is nearby......Thanks for listening...
  4. T

    Need pic of adjustable FpR

    Re: Need pic of adjustable FpR It was under the vacuum port...sorry I didn't explain...
  5. T

    Need pic of adjustable FpR

    Re: Need pic of adjustable FpR That was it...thanks
  6. T

    Need pic of adjustable FpR

    I have simple question...I had adjustable fpr on my syclone installed years ago...I can see FPR/diaphragm..where is screw for adjusting fuel pressure..I can't find it and need to adjust FP..thanks
  7. T

    trouble at 2500 rpm

    Re: trouble at 2500 rpm Well, that did not seem to help...now I get TPS code....Walbro pump is 1 year old....I did notice that when i floored it, I could not get above 100mph,,truck does ok from 60mph to 80 mph....I guess I will look into TPS...any help appreciated...thanks!
  8. T

    trouble at 2500 rpm

    Re: trouble at 2500 rpm i appreciate recommendations...no knock....adjusted Fp from 48,50, 52, 54, 58.... 54 psi helped some...mechanic felt that vehicle should be downshifting at 2000-3000 RPM at point where i noticed the problem...do I need to have transmission solenoid looked at..or any...
  9. T

    trouble at 2500 rpm

    Just did new cap, rotor ,plugs, new IACV valve, all sensors good; truck idles OK... truck pulls well above 60mph; however at 2000 to 3000 rpm as truck shifts/boost kicks in--ther is hesitation/almost like the engine is pushing against a wall; however, if i punch the accelerator quickly it...
  10. T

    Tightening up the front suspension?

    Related question Related question I have Syclone 42 k miles; has rear sway bar;using enhanced alignement specs; new front Monomaxs;good balljoints;new tires;has stock swaybar w/ polyurethanes;I lowered Syclone 1"w/ torsion bars to improve cornering; mechanic says I need new idler arms; I have...
  11. T

    shifter cable adjustment

    Just as an aside Just as an aside Since we're talking about shifter cables, how many hours of labor should it take..had mechanic replace broken one...it cost 2 and 1/2 hours labor ...is that right?
  12. T

    Blinker--washer crap

    This has been discussed before...everytime blinkers are used, windshield wipers activate...since I only drive in good weather(never rain), what would be quickest way to disconnect windshield wipers.....
  13. T

    IC relay hotwire

    Followup Followup This weekend I did hotwiring. After removing bracket, intercooler relay and harness did not want to come apart easily. I ended up pulling out yellow wire with its connector from the harness(no cutting); since yellow wire had its terminal connector end in place, I grounded it...
  14. T

    IC relay hotwire

    I have ready the posts and archives about this topic...Let me see if i understand. There is a intercooler pump relay connected to a harness/plug. If I disconnect the relay from the harness, the pump will always be "on" with ignition being "on". What confuses me is where splicing to the yellow...
  15. T

    Trans temps

    Reply Reply I have stock tranny, bigger transmission pan, completely B& M trickshift fluid, and my temps are around 180 degrees.
  16. T

    KB air intake vs. Stock crossover setup

    fenderwall cutout fenderwall cutout Something I did..left battery in place..cut hole in fenderwell,put screen over it and ran K&N to turbo..no problems..then cut out heat shielding to keep heat away from K&N/tube leading to turbo
  17. T

    Throttle Body Idle Screw Adjustment

    idle screw idle screw Where is the idle stop screw/where is this cap? My dilemna is I tried to remove IACV except pintle/valve portion can't be removed.It wiggles but for some reason the diameter of the pintle can't get past the opening.So now my vehicle idle is consistently high. My goal was...
  18. T

    toluene & o2 sensor

    followup question followup question I have a digital meter; how would I use it to check to see if its functional? Any ideas appreciated...Thanks
  19. T

    toluene & o2 sensor

    Does chronic/ 1 gallon per tankful of Toluene affect O2 sensor;over last two years (over 3000miles) I have been using Toluene, but wonder if it is affecting O2 sensor(too rich Code)??Any input appreciated....
  20. T

    Tranny fluid

    I have switched to B&M trick shift fluid completely...feels smooth...any feedback?
Top