Search results

  1. T

    I need to decide wich guage to put in the last hole.

    Question Question I am installing trans temp guage(B&M)...If I were to place temp guage to monitor intercooler temps, would I run temp sender into what? line..any suggestions...what setup are you using...thanks
  2. T

    350 related question

    Not exactly a typhoon question: Typhoon look alike blazer has 350 engine(84-87 350 with adapter for TBI)/hypertech chip/custom flowmaster without cat ;had fuel pump change w/in year; when I jump on accelerator from standstill, it hesitaes or installs;if I take sharp left(but not right) turn...
  3. T

    350 related question

    Not exactly a typhoon question: Typhoon look alike blazer has 350 engine(84-87 350 with adapter for TBI)/hypertech chip/custom flowmaster without cat ;had fuel pump change w/in year; when I jump on accelerator from standstill, it hesitaes or installs;if I take sharp left(but not right) turn...
  4. T

    Racetronix fuel pump harness - phrase

    I am planning to upgrade to Racetronix fuel pump; if I buy new gas tank for this install, then will avoid having to take off the bed from my Syclone...also is the gas tank the same as a "91 S-10, and where would you get the best price? Any help is appreciated...
  5. T

    Accel dfi

    Any thoughts on value of this item on E-bay--would it be worthwhile for Syclone tuning??Any advice appreciated....
  6. T

    Rollpan

    I am Syclone owner, but also have 91 s-10; I would be interested in replacing rear bumper w/ rollpan; what brand do you suggest---Summit versus Sir Michaels versus APC versus any others---any suggestions would help...thanks
  7. T

    Famous propshaft question

    Before I purchase Al Dustan's propshaft, have any of you tried Autozones front propshaft listed under CCT 1993 GMC #12-357? 162dollars...I found this listed unde the archives..Thanks
  8. T

    Famous propshaft question

    Sorry for so many questions...I am wondering what the pilot diameter is ?(at transfer case phalange)....thanks
  9. T

    Famous propshaft question

    One more question....I contacted the websites you listed...Do we have a round or square shaped surface where the CV bolts and what is the distance from face to phalange(26.5 in or 31.5 in--I guess not including the propshaft??) Thanks for your help.....
  10. T

    Famous propshaft question

    After replacing boot on original propshaft it came off within a hundred miles....After reading as many posts as possible, I could get Autozone version(12-357..any opinion?), probably won't get NAPA(bad opinions from the posts)...would could consider Al Dustans versus Dynotech/ATR version.....I...
  11. T

    Fuel Pressure Guage

    Has anyone attached a fuel pressure guage where the fuel filter meets the fuel line...versus the Schraeder valve... any other thoughts...either way, should i use an electric or mechanical unit to monitor my Fuel pressure while i am driving...any help appreciated...I have stock fuel pump and...
  12. T

    trans temp gauge

    Do any of you have the specs on the brass fittings/parts needed....I have looked in Summit and don't want spend 80 plus dollars for a transmission filter kit..all I want to do is install a bigger tranny pan and hook up a reliable guage to monitor transmission temps... ant help is greatly...
  13. T

    EGR Plate

    Interesting EGR mod!!! Interesting EGR mod!!! After reading S10 planet.com website, I discovered that someone had modified the equivalent of the EGR blockoff plate so that there would be some flow through the center of the plate. Supposedly, this will prevent codes from going off...Check out...
  14. T

    Exhaust /More or less restrictive?

    Well, I just redid my exhaust. Took original exhaust mufflers and pipes off...then from cat back ran 2 1/2 in aluminized piping w/ total of three bends(compared to 4 bends w/ stock) ...used a warlock muffler and continued the 2 1/2 in piping to a 4 in oval tip by Ractive(sweet looking)...Since...
  15. T

    DriveShaft/Propshaft Safety Loops

    Speaking of safety loops, has anyone tried the one listed in Summit's catalog....would it work?
  16. T

    Where to find best price?

    I am looking for best place to get Catco(catalytic converter) and bigger front sway bar w/ polyurethane bushings..any help appreciated...
  17. T

    Scanmaster SYTY

    If the price is under 300 dollars, count me in.......
  18. T

    Wiring IC Spal fan???

    Would you have a pic of your fan setup to the CCHE...just curious since I have put on a custom intercooler scoop but would like to keep CCHE cool between stoplights.....
  19. T

    need turbo oil return hose

    I believe the forward turbo oil line is the orange one...my mechanic used some power steering hose; I can't remember what size hose? was used for return line but was easily obtained at local auto parts place...
  20. T

    Metal Skidplates - who sells?

    You may want to take it to a look sheet metal shop--they can fabricate a skid plate from steel( using the original template..worked out well for me...and its steel--much better than plastic or aluminum...
Top