Search results

I have the case apart and cant figure out how to get the viscous off. while searching all i could find was a george blake post saying it'll come off when you put a gear puller on the bearing. Does that work or do i need someone with a press? Thanks

Is this chain too loose or should I just replace it anyways. it has 115,000 miles on it

Ive searched and searched with nothing but a george blake how to remove the tranny. Ive got the tans crossmember off ive unbolted all of the brackets and took out the 5 bolts (thats all i can find) that hold the transfer case to the transmission. Nothing will move, not even a little bit. So...

I did the research on here and when i got all the bolts loose and try to jack up the cab it wont lift off the rail but brings everything with it. I loosened all the mounts and removed the two bolts that hold the bed and rear cab mount together. what did i miss?

My heater core died on me and my dad tried to tear into it before I did but he didnt read up on it first. he got some of the panels off and at some point during all of this he moved the truck and realized the radio wasnt working. He hadn't touched the radio up to this point yet. When the...

I'm working on putting the last piece of cladding back on the truck. It's the front wheel arch on the passenger side but the part that connects up front just behind the bumper cover was broken when i got it. Has anyone rebuilt that piece or can anyone remake it?

I just got mine put in primer and I know I've seen others around on here. so post a picture if you got one

if i buy this http://www.amazon.com/3M-5895-3M-5895-PRO-EZ-FILL/dp/B0013HDSGC/ref=sr_1_2?ie=UTF8&qid=1314635824&sr=8-2 do i need to buy anything else to make it work or is that all that i need to repair the cladding peices Thanks, Graham

Looking to buy a lower mile fully functioning front diff for my syclone. Not really sure on a price so i was thinking 150-180 is what im looking to pay. Thanks Graham

I made the new intake and am trying to cut off the heat from the engine and came up with this on a first try. Do you think it would have any advantages taking all the air from the fender holes and putting it into the box?

This trucks really starting to be a pain in the ass. So I hardly drive the truck being in school but have alwayys had problems with the rear wheels spinning without really giving it any gas. So I put it on jackstands and the front wheels arent even pulling. SO search got me nothing, what do I...

Cladding falls under body I would assume so I'll post here. Bottom line is i have a front bumper cladding piece that was in a collision has minor rash and a hole cut out because there was a dent (hole cutout to try and repair. basically a failed attempt). But overall its in good condition...

Finally got around to logging the truck with data master and was hoping someone could take a look for me. It threw a few codes and not sure where to start http://rapidshare.com/files/451914730/drive1.uni

On a datalog in tunerpro one "capture" shows almost 13 degrees of knock retard. My question is throughout all of my datalogs my waste gate duty cycle is 99.61% no change at all it just stays at that. The truck shows knock whenever it should be entering boost but the turbo (psi) reading on...

What sensor is on the driver side between injectors 3 and 5 and is there one or two wires going to it? I was doing a compression check and the sensor was broken and it looks like 2 wires should go to it but theres only one so I'm not sure if its right or not. Thanks

So, i have a leak in the A/C at one of the seals and am looking to replace and run freeze 12 maybe. So first question would that be easier to run than R134a ? I know im going to need a set of these...

Does anyone have a datamaster copy they'd sell or is it easier to just get one off of a vendor?

Could someone send me a tunerpro file of a good running stock truck with a 2-bar MAP? I'm trying to figure it out better and be able to see what areas my truck could use help in. Thanks

Driving through Burlington NC today and saw an Orange typhoon for sale didn't have a price i think just a number. I got pictures on my phone but cant upload them but it looked really well done.

I'm on spring break so have a chance to try and get it right. My truck runs good but after letting it idle for a little bit it runs rich, give it some gas and after a couple revs the check engine light will go off it's a code 34. While driving it runs strong up to about 3000 rpm's (only run...