Search results

Re: Vent in fenders/cladding While I was working on them I took the time to smooth out all surfaces of these fenders. For now I just sprayed them with Rustoleum.. Jose didn't do the greatest job laying them up and there are lots of voids behind the gelcoat. I've had many areas...

Re: Wider than stock diff? I run a ZR2 rear with 4 front rims and I made my rear cladding 3/4" wider than stock. Everything is flush that way.. Don't forget that if you do use a ZR2 you also need to swap out the ring & pinion to the proper ratio..

Re: WTB: Ty Aluminum Driveshaft X2

Re: Vent in fenders/cladding LOL, I like that answer, I already have the fenders removed and I'm just about to prime them. I'm not going to put them back on just to test air flow in this area so this sounds like the best answer.. Once they are reinstalled I'll test airflow, if the are...

Re: Vent in fenders/cladding There is room to glass a duct right to the back side of the fender. What are your thoughts? Would that area pull air out or push it it?

Re: tps #$%@ F13 is the correct terminal and there is not another one that you can use. I splice off of this with a 2nd GM ECM and use this to control my 80e. If you have everything hooked up and grounded properly I bet there is an internal issue with the TCI controller..

I'm in the process of body-working my fiberglass fenders and I'm throwing around the idea of cutting this area out and making a duct up to the top of the fender. My thoughts are that this is an area of strong negative pressure it it will suck (hot)air from the engine compartment out of this...

Re: Fiberglass Front Fenders with Cladding So I spent the whole day yesterday cutting, re-glassing, and body-working these fenders. It takes quite a bit of effort to make these truly nice.. To start I taped off the outside then painted white gelcoat in from the back: I let that just about...

Re: Blank Chips Moates.net does but do yourself a favor and just buy this: http://www.moates.net/ostrich-20-the-new-breed-p-169.html?cPath=95

Re: Fiberglass Front Fenders with Cladding I'm finally getting around to painting my fenders so I decided I'd "fix" the alignment issue... Pulled fenders from truck: Marked out line of where to cut fender: Cut and re-positioned end further forward to match other side: I took tomorrow...

Re: Code59/tunerpro help That should work. I don't recall exactly where the B9 wire goes to get grounded but it should be sufficient..

Re: Re-clear coating stock rimsg- DIY Will do.. I referenced your thread while doing this.. Good tip on the 3M pads.. They worked perfectly.. I highly doubt that this rattle-can clear will last nearly as long as your POR-15 product..

Re: Code59/tunerpro help As far as the AutoTunes go.. For the longest time there wasn't one that worked with TunerPro5.. When I got into tuning a couple years ago I hated trying to manually edit the VE table so I started working on my web-based auto-tune.. I was trying to figure out exactly...

Re: Code59/tunerpro help I think it just sits static at the last value of the table as long as there is no knock or anything.. I spin my engine up to 6k with Code59 and it works fine..

Re: Code59/tunerpro help Which AutoTune are you trying to use? There are 3 that I know of.. * The spreadsheet * The App that Renz wrote * The Web Based version that I wrote.. Clearly I prefer the version I made. You can access it here: http://mattw2.dyndns.org:81/cgi-bin/AutoTune.pl Its...

Re: Code59/tunerpro help I wish I knew how to edit the code of a bin and make those sorts of changes.. What you probably remember reading is that a single main fuel table was created so that you don't have to edit multiple tables.. I don't recall if Dig did that or someone else.. Here is a...

Re: Re-clear coating stock rimsg- DIY All done. Installed my BFG G-FORCE SPORT COMP-2 tires and used the stick on wheel weights that go inside the rims this time around..

Re: Code59/tunerpro help If you have an emulator than you want the RT version.. Sorry, didn't think about that. The XDF defines what parameters will be available in that tree and tells TunerPro where that data is stored in the bin. If you expand Tables, for example, you can select a table...

Re: Code59/tunerpro help To start off, make sure you have the latest version of Tuner Pro. You can download it here: http://www.tunerpro.net/download/SetupTunerProFree_v500_8853.exe Next, grab these XDF and ADX files: http://mattw2.dyndns.org:81/code59/Code59_3Bar_1.6_V25%20TP5%20ONLY.xdf...

Re: Code59/tunerpro help What are the issues?