Search results

Squid, I seen one on FB pop up in PA recently it was eight hundo. At one point I also was after one and it took me 4 years but I found a pretty good one for 200 in a original box. When I searched everything that was on the market and available was a typhoon bumper cover already painted. At the...

What's wrong with the other 2 where are they bad?

I have to do this to my truck, ASAP. I determined that I need to remove the steering box from the steering shaft, remove pitman from center link then completely remove the steering box from truck. I guess once it's all out it possible to remove the pitman from the box on a bench top. Seems to...

I ordered a set of the gasket/oring from local GMC dealer. Come in 2 pack I believe I still have one left. They are pinkish brown color.

Years ago I had my truck up on all 4 and was able to do the pan by jacking the engine. Of course I had removed the motor mounts. I ended up replacing the timing cover with a updated billet design, and a " more accurate" timing pointer. After getting the timing cover I realized the pan had to...

Yes it's just vented. I have the factory tube that would originally go to the front airbox still connected. It rests up by the remote oil filter location. I did not want to remove it and have a open port back there. Occasionally I see a little steam stuff puffing from the hose up front. PCV...

I appreciate the information on the needle flipping topic, I was more or less trying to pin point on WHY it triggered the needle to go over board and why I discovered the dip stick popped. I have a easy non invasive way to fix the needle. I just rotate the cluster until the needle goes back...

If you can't find parts you can try to source one from a AWD astro/safari van.

Noticed my dipstick popped and oil gauge flipped Happened after I started it and ran,turned off an started again shortly after. Any ideas? PCV is intact. Aftermarket intake. One plumbed into the intake, the other goes to throttle body. Driver side I have the original hose hooked up that goes...

Is there any way I can intercept the coolant signal wire to the dash gauge within the cabin of the truck? Specifically a place to look for the wire ? What I am trying to do is temporarily install a auto meter temp gauge I have laying around in a box, and see if it responds different in the...

I think ones steel. Ones aluminum.

Wow I'm surprised. When I sourced mine- when I had inaccurate readings on my gauge I pulled the part number from racetronix. That's where I got the Delphi number. It was 70 or 80 dollars through them, plus a bit of a wait for it to arrive. I think I landed mine for around 30.. hasn't been a...

I bought a Delphi brand one it seems ok. Had inaccurate reading on my gauge, replaced it. I don't have the part number on hand but I saved the box like a pack rat.

Being the parts are off a shared vehicle platform the ports I believe are coolant passages used on ZR1 Corvette platforms. DaveP is seemingly a expert with that topic and I don't want to cross too far into that territory. I believe there both capped on our vehicles.

I have a extra pcv T in my surplus if you don't have one. Couple pictures of the VECI- brand new one I had in my surplus. Pretty clear to read if yours is faded, or peeling back. Mainly dug it out so you can decipher the emissions hose routing.

My gauge barely moves. I noticed it's active when I engage the key on- it moved a tad bit up. Was always concerned also- thinking something was up. I do have a scan master G that does verify correct temperature. The correct sensor is the single wire located on driver side cylinder head single...

Charcoal canister plugs? There's only 2 hoses that go to the lower portion of the front driver side lower engine bay- where the charcoal canister is. 2 hoses go into it they are labeled fuel with arrows. Being that the charge air cooler was removed in place of an air2air those plugs were...

Correct the single wire is a thermocouple connection, and the brown/black is the power for the pump for the original liquid chilling system.

Gauges seem to start to function. Fuel gauge level off at a half tank. Was wondering if the factory temp gauge was connecting and I removed the single wire connector and re plugged it back in. When I had the KOEO I saw movement on the needle. I guess temp gauge is so inaccurate it doesn't read...