Search results

Re: New Source for Throttle Body bore & Bearing upgrade I can't remember how much it was, but I remember I wasn't strtled by the price. We even talked about mounting my alky nozzles in the TB and they appeared to be able to do that kind of work and even a little interested in it. Just give them...

Re: New Source for Throttle Body bore & Bearing upgrade I can vouch for the work done by the guys at San Diego Carb&F/I. dropped it off tue. morning, had it back on the truck by wed. afternooln. reasonable prices,great work, and now NOTHIN'S getting out of my throttle shaft seal. You can call...

just like it says.per s term and l term values, I'm running pretty lean around town, but before I do anything could someone give me their thoughts on what my datamaster files show? I haven't checked anything o n the truck yet, but any advice in helpful. Thanks, Jeremy SY2185

Ive got an ultima in the bed on the front pass. corner with 1/0ga. pos and neg through a quick disconnect to a starter sol. next to the batt. with 1/0ga running from the switched side of the sol. to the starter (that way the 1/0 is only hot when cranking).connected to the always hot side of...

Re: SoCal roll call... Yeah, had some side projects going for a while there and had to take leave from the sy/ty world.Actually, I checked in a month ago b/c I needed paint codes for my sy to sell it and get a more normal vehicle. But since then I figure why do any work on it at all if I'm...

Re: SoCal roll call... Still surprising ppl. in SanDiego w/my little truck. Jeremy

Re: Turbo Fluxuation wierd,your tcc doesn't lock up till like 68mph.

Re: Miss at Idle I second that throttle body shaft idea. I just had San Diego carb&f.i. rebuild mine and my idle is now dead on@625-650rpm, I don't lean misfire when at the smog test station, gas mileage went up 20%, boost control leaved out completely(vac. leak@idle is a boost leak under...

Re: after replacing ign. switch.... you it was the 2 little coppper tabs that covered one of the ign. bolts. they'd crossed up and were touching when I put it back together. no biggie. thanks, guys. Jeremy SY2185

so I rplcd my ign. lock and now w/o the key in the light sounds when u open the driver's door like the key was in the lock.before it comes apart again, anyone know what to look for? J

Re: The best motor tie downs anyone who wants/wanted one if you got no response I'm sorry call me @619.920.4077

Re: ABS Delete Kit - Catchup Run I paid via phone awhile ago. I had no idea anything had happened and just wrote off the transaction as whatever.I'll pm you. Jeremy

Re: The best motor tie downs sorry guys, found like 5 more. anyone wants one just send the $ to my paypal add.: jd2326@sbc.com will ship asap after payment rcv'd. Jeremy SY2185

Re: Trans and oil cooler question hey Tom, Are you saying 150F at the sending unit in your manifold just before the rad? And that's coming directly out of your trans? What type of conv./setup you running? Jeremy SY2185

Re: Temp gauge install for tranny i'd say it's very important that the sender goes on the output of the trans, right were the fluid will be the hottest. I have 3 senders-1 in my TCI pan,1in an autometer trans temp. manifold(the only way to go)8" from the trans on the output line and 1 coming...

Re: Pics of progress on Sy #434 Sick ass! Just remember- when using ss hose to use plenty of"adel clamps" available from earls,etc. That ss hose will eat through anything it's touching in time,esp. an edge of a body panel,etc.you can also help this by putting shrink wrap over the braided...

Re: cbr brake kit on e-bay Interested in buying mine? I got some junkyard spindles and cut them up so I could just swap them with my orig. ones when I did the kit(yesterday and finishing up tommorrow). I paid $50/ea for the replacements, and shipping on those heavy bitches won't be cheap. Hit...

Re: shifter my B&M magnum grip pro stick fits perfectly in the stock shifter hole, just w/o the leather boot. It's mounted similar to mike lee's. shifter was just over $300(w/a Morse cable) and installation(drive in stock, drive out new shifter)was only $100. And the guy even modified another...

Re: Thermostat just passed my ca smog test w/a 160 therm. and my ic pump running.No problem! Jeremy

Re: please take a look at my DM file holy crap. that wasn't supposed to be 4.1 bar was it? Isn't 1 bar 14.7psi? 60.27psi static FP seems mighty high. Especially if you are running lean w/that much FP you should really keep off it until you figure out what's wrong. I'm going to look at your...