Search results

Re: Vac/Boost leak @ Upper IC to TB does this look right? I have not seen another SyTy motor in person to recall if this looks right. The clamps say " Aero Seal BREEZE"

I sealed off the inlet hose and pressurized the intake system w/ 10 PSI with the motor off w/ my air compresser. Anyway, I found a big vac leak at the hose fromt he upper IC to the Throttle body. I tried re-aranging the clamps, changing the hose around, tightening the clamps down to the max...

Re: PCV Bypass Im meeting w/ a local Sy owner this weeking and will be getting some DM runs in. This should point me in the right direction. I don't know what I did, but it is idling much better now (well in D at least) and doesn't miss anymore. I see one or two red flashes of knock w/ my...

Is it safe to remove/bypass the pcv system? I don't like all the oil that ends up in the turbo, IC and intake. I will cap the ports on the intake and TB and put K&N breathers on the valve covers. Is this safe, or does it actually need to be sucked out of the crankcase via engine vaccum? I...

Re: SyTy Appraisals----? Well I just got mine registered and the DMV said it was worth $3100. And I thought I got a good deal @ 6500! I wasn't about complain, I thought I was going to pay tax on the KBB retail value of 17K, so I saved over 1K in taxes! :tup:

Re: Need DM cable. PPI Typhoon? Anyone? Add me to the list as well....

Re: Ty runs the same w/ a plug wire removed! Well after a big ordeal trying to change the wires/cap/rotor/ignition module, it is back the way it was before I started. I found out what was wrong (very stupid mistake that cost me 3 hours of swapping parts around and two trips to Summit :roll...

Re: Ty runs the same w/ a plug wire removed! cool. Glad to hear you found at least one problem! I did that once too, but I realized it as soon as I started it up. I replaced all my hard lines and elbows with sillicone vac line, so that can't be a problem w/ mine.

Re: Ult. V9 doesn't work well w/ 3Bar is has: C3B16V, then it has something blacked out with a "11" below it. Should the white numbers on the stock chip be facing up or down when connected to the ultimate? I tried it with them facing down and the truck ran poorly. With them facing up, it...

Re: Ty runs the same w/ a plug wire removed! I had the iridiums lying around. I can get anything summit carries here in town. The retail store is 15 mins away. they didn't have any taylors in stock. Whats wrong w/ Accel?

Re: Pulled and disassembled my engine today. Found a 4" piece of metal, WTF??? Is it the same type of material as a coat hanger or is it kinda springy? I have see pieces of main seals end up in oil pans, but that is mainly springy metal, unless the syty seals use a soild piece of wire/metal....

Re: Ty runs the same w/ a plug wire removed! Ha sounds just like mine. :roll: We took it inside a shop to have a couple other guys familar with SyTy's look it over and we hooked it up to a Snap-On scanner and couldn't come up with anything with that. They mentioned that they smelt lots of...

Re: Ty runs the same w/ a plug wire removed! Compression is good (140+ - 150 on all 6) Timing is set at 0*, TDC has been checked. All the plugs looked good. none were washed out.

Re: Ult. V9 doesn't work well w/ 3Bar Yea, I got a brand new MSD 3Bar chip directly from Summit. I also tried the 3Bar that the truck came with (uninstalled)

Im waiting on my datamaster cable, so I figured I would mess with the Ty somemore. Well I removed one wire from the dist. with the truck running and it didn't seem to make much of a difference. It actually smoothed out the idle a bit, but the throttle was not quite as responsive. What does...

I swaped in my ultimate today and it really gave my truck a nice boost. After wondering why it works good now and not before, I remember I didn't swap in the 3Bar MAP sensor. I have tried two different 3Bar sensors and both made the truck run poorly, (wouldn't idle, would throw a "running...

Re: Random High Idle I re-checked the codes and it was a code 35, not 32 like I thought. Its described as "Idle air Control (IAC) system problem - can not set desired RPM" What does this mean on these trucks? I don't have datamaster yet, I am trying to get a cable. I wasn't home last...

My Ty has been idling around 6-700 in gear, which seems to be normal (besides the miss every 15 seconds) Anyway after driving it around for a while today, the idle in gear jumped to 1000 and in neutral it is over 1500. The CE light came on and gave me a 32 code I think (IAC not able to control...

Re: I Give Up. I set it to 0* with the wire disconnected. Then reconnected it to drive it. It runs better with it set at 10* inital advance (set with wire disconnected). I will order a cable today.

Re: I Give Up. Any idea on this?