Search results

Trans #3 is toast and I'm tired of building/buying them so I decided to do a full on stage IV transbraked 4L60. Waiting for my new core to show up(3yr/36k mile GM warrenty) to build up on. Here's what I figured the tranny will need around it, any suggestions appreciated- poly engine/trans...

Since I have the trans out I'm gonna do a few things that are right there. Aside from poly motor mounts,CVR starter, reroute and shorten batt. lines to bed, and stainless hose to rear mounted trans cooler instead of front mount and fix my damn weeping turbo oil line. My question is about the oil...

Check out my gallery on chitown's site, finally got a place to show off all this shit.Thanks BW. http://www.chitownsyty.com/gallery/view_album.php?set_albumName=represent What do you all think? Jeremy

Took the sy out for a drive at work a little while ago. It was run at the track last Sat. putting 7-8 1/8mile runs on it w/no problems. Earlier that Sat. I'd finished my remote spin on trans filter in-line w/ my big 6 row trans cooler and disc.'d stock cooler. Performed great at the strip. Took...

Using the innertube method last night looking for a vacuum leak that's getting worse, I opened the throttle to make sure the hiss wasn't from the air going past the throttle blades. All of a sudden my leak was gone. Wiggling the throttle shaft(very little play) made it come and go, but only at...

My Permacool remote trans filter lists the Fram (for reference) PH8A or PH43 as correct filters. Problem is both of them are plenty bigger than the adapter, and space is non-existent. Though one's shorter, it's not the length that's the problem. I found a PH46 that'll fit and is the same...

I asked this a while ago but can’t remember. I’ve got a 9”x14” 6 row tranny cooler in front of the rad./ ATR IC and want to know if I can leave out the stock in rad. cooler. I just relocated the battery to the bed and want to put in my ATR cool air kit- hence the questions. I had braided lines...

I know with the battery in the bed behind the passenger's seat I need a master battery cutoff. Does it have to be in a specific place? I'd just a soon put it where the Pos. cable extension joins the factory lead. I know several members have researched this already, what'd you find out? Jeremy

Checking/gapping my plugs right now for alky and noticed blow by/ fuel deposits on the #4 plug. Seems the plug wasn't in all the way b/c the oil dipstick tube forced the socket more and more at an agle as the pulg went in. I don't belive the hole is stripped, or cross threaded to much, just the...

50/50 WATER ALKY OK IN smc kit? I put the 220uF cap after the fuse on the feed before the relay. OK? Wouldn't ti drain the battery? What pump speed do you all run at w/ which mixes? I break up over 4 on straight alky turning on at 11 psi w/stock boost levels. Jeremy Orig post here...

I've got a stock motor and chip in my sy w/plenty of bolt ons. I've recently gotten pretty serious about racing and now have an SMC alky kit and factoring in WG adjustment, fuel pressure, alky mix/turn on point and tire pressure/launch boost,etc. it's getting pretty crazy. I've found noone that...

check it out- from the archives http://home.att.net/~stevemon/AlcoholInjMod.html Jeremy

My windshield wipers were coming on when I used the turn indicator b/c the lever was all worn out. $122 from dealer, =/-$90 from gmpartsdirect. Then lo and behold it's on ebay for $40. Now that I've got it the manual outlines how to replace it but says nothing about how to get the old one out...

I was checking my tps% vs. accelerator pedal movement(have to floor it to hard) and apparently my TV cable was a little tight, holding it up. Except I noticed this while turning the thrpttle arm by hand, and before I realized it was the TV cable I heard a snap from the adjuster area and gained...

Find a NAPA auto parts store and get PN 819-5738 Ford tailgate support cable. I cant find it on their website- http://www.napaonline.com but all you need to know is it's 17 1/4" from end to end. Remove the pass. side 15mm alternator bolt(the lower one it hinges on) and put it through the...

Where the hell did I see this? Someone used a brass spigot/shut off on top of ATR/Hayden cooler to assist in refilling. Also, anyone have any pics/know how to mount this cooler with a trans cooler up front also, or does the trans cooler have to go under the bed? Thanks, Jeremy

1/8 mile in SD. Took the MR2 by .919 sec in eighth, the VR4 by .157. MR2 had those neat scoops from the decklid to the roof and some cool gauges, controllers. The VR4 had an Apex-i fuzzy logic boost controller and an in car laptop setup like ours. Unknown what else. I've got pics of me vs. the...

Ran a good 0-100 run on DM and have a few questions. Truck has a fresh semi-performance motor,jabsco,255hp walbro, afpr(currently at 47lbs),aux. IC, all tune ups done(plugs wires cap rotor fuel filter air filter PCVs,etc)and IC line relocate. I'm still working on my oscillating boost but my...

Got low boost- waht's my file say?I'll e-mail it. Jeremy

I too have the all to common 10 psi boost problem despite otherwise running well. I read every post here with the word wastegate and scoured my manuals for every mention of it. Yesterday I replaced the vacuum elbows and hose from the solenoid to and from the turbo and wastegate. I tested the...