Search results

I've got 3 IC brackets, a horizontal one that attches near the TB, a straight one, and a curved one. My Sy only had 2 of them when I got it and I think 1 was in the wrong place. How do they go(straight one bolts to the front or rear of the ex. man.,and front,middle, or rear of IC?)and which hole...

I'm putting together my new Hartman trans using the case from my blown up GM SRTA trans. Brian mentioned that my valvebody(surprise!) is not a sy/ty piece, but my last trans was my 3rd one so who knows when I lost the original. Since I'm going with the full manual transbrake I decided to use an...

Hartman said he'd never seen anything like it. Ouch. Now putting it back together. Good times. Jeremy

Ordered some new Moroso flexplate bolts to go with my new SFI B&M flexplate. Everything's ok with them, except they came with a washer similar to the ones used on grounds(not much bigger than the bolt head, and all around the outer edges they're cut and turned at an angle like to cut through...

I can’t find the nuts for the center poly mount-adapter bolts, and no way am I pullin one of them to go to the hardware store w/me. Anybody know the size and thread of the nuts, o even just the bolt? Thanks, Jeremy

Just like it says. I don't need to pull it out, just align it w/the tranny. Jeremy

That's just about the whole question. I'm no master auto electrician but I do make a living fixing copper wire carrying +/- 280vdc across 35k'+, so I'm all over capacitance, sectionalizing faults, current draw, loss, etc. I just would like to know how I could get either a 3pole lighted...

Heard from a respected sy/ty vendor who's also selling my the WG that after securing my int. wg so it's non-operational I could plumb my new ext. off the WG soleniod just like stock so the ult. can control my ext. wg. True? if so, sounds great to me. Jeremy

I have an Optima in the bed w/2ga. to a Summit starter sol. under the hood on pass. side. Same 2ga. to the starter, the last 3' wrappped in Earl's fire guard. The factory neg. cable bolts to a tab welded on the frame rail at the rear of the pass. wheel well and 2ga. goes to the frame from the...

Are there any sensors in or using the stock shifter? I remember once I had idle problems and found it was a misaligned park/nuetral switch making the ECM think D was N and running low idle. Other than the shift cable anything else needs attention before the swap? Jeremy

Can I run mid/high 11s like this? Trucks down now for Hartman kit, 9/11,and poly motor mounts. With this done I get to look for a turbo to complete my SY's powertrain. Seeing 10s on stock ex. manifolds means I don't have to go headers and aiming for 11.4-11.8 keeps my stock heads and cam. Makes...

Finally found one. I didn't think my 9/11TC would want a trans blanket around it keeping it warm, but found these folks here who offer a shield for $125. We'll see if it actually fits. Jeremy http://www.campbellenterprises.com/transmissionshields.htm

I noticed the plastic top piece of my knock sensor turns left and right independently of the threads into the block. Is it OK, or did I break it while doing my trans/ motor mounts? The trucks not quite running yet, and still has the trans out giving me great access to the sensor. If it's broken...

I know one fits better than the other(Derale or deep GM pan), anyone know which it is? Jeremy

I just typed the address in the search field at altavista.com and at the end of each of the results there's a translate button. This is the link just translate on the bottom across from"translate a website". To link around in the site I found it quicker to right click and select open in new...

The thread pitch of the adapter the trans cooler lines screw into at the trans has the guy at the local Earl's shop stumped. I need 2 90 degree whatever thread to -6AN male/male elbows to plumb my in bed trans cooler and remote filter(not using the stock in rad. cooler at all). Could it be...

Got the trans out and I'm in the process of installing my poly motor mounts. Being a glutton for punishment, I'm leaving the motor in. My question is do you all recommend dropping the front diff and leaving the ex. manifolds/turbo on or would it be easier to just pull the manifolds and go...

Motor's still in(barely) nearly all else under the truck is out. If anybody needs any detailed pics of whatever(Rick and the purple wire-sorry I was too late) post here and I'll e-mail you whatever you need to post, whatever. Though my effort's well financed, it still takes awhile to get (get...

Mine leaks and the trans is out- remember hearing AR offered a stainless line with -AN fittings that fed from a new location- possibly at the remote filter. Anyone know about this? Is that the right location? Tried AR by phone a few times, no answer(everybody's busy incl. me). I can do the hose...

my cooler's under the bed now with my remote filter and a pull fan pulling air down through it from above. While shopping for a huge cooler I found some interesting info about pressure drop, efficiency ratings, etc. What do you all recommend for my set up in like 16x11" size with threaded ends...