Search results

Re: Stuck rotor button I just did the hammer chisel thing on mine. Other option would be pull dizzy and cut it off CAREFULLY with die grinder and cut off wheel. Good luck.

Re: Sy 1028 at Muncie (timeslips) This truck has always seemed to have some KR. I can get a couple degrees in neutral by just blipping the throttle. Now I'm pretty confident that at least some is not false knock, so before I go back I'm gonna try some Torco and see if I can get 0 knock.

Re: Sy 1028 at Muncie (timeslips) I launch with 2 to 4 psi, that's the sweet spot for my truck. I plan on going back in a few weeks when it gets cooler out.

Re: Sy 1028 at Muncie (timeslips) Forged bottom end, 30 over, stock heads, cam, turbo, AFPR, ATR aux intercooler, dual intercooler pumps, and the Ultimate.

Re: Help! Fixed timing now No Power TPS% is 100 in both however TPS volts is showing almost 1/2 volt difference:dunno: might want to check that.

Both runs I was in left lane. Both runs were against Mustangs. First was a GT 500, not sure of year but supercharged and manual tranny. Second was a new 5.0 with an automatic. The temp was low 80's and humidity wasn't too bad. I drove the truck an hour to the track so I had heat soak issues. At...

Re: lots of smoke at idle It's the seal on the exhaust side. When cold no smoke, as it gets hotter it starts to burn off. At idle there is less air flow meaning more smoke that you can see hence when you're driving more air through the exhaust with same amount of smoke it gets diluted. I had...

Re: Saudi Syclone - 2612 Does the dp hit the tower because of the solid mounts? If so you may have bigger issues than the dp, I would bet when you get the radiator and shroud installed the fan is gonna be against the shroud. From the pics it kinda looks like the engine is not centered between...

Re: Awesome Ty for sell in Germany Best looking "fatman" seats ever

Re: What did you do to your SyTy today? (part 2) Changed the idler arm that got trashed at Nats during AutoX.

Re: Nats Recap & AutoX Results Plate # TK927LNE is me, Nats virgin, AutoX virgin. Huge thanks to everyone who made this event what it was. F#@!% rain :rant: Thanks to Harmon for the ride to the ATM (imagine AutoX on public roads, you're an animal) Idler arm did not like AutoX, it's shot

Re: Not sure if this is the right area or not for this I would assume you are talking about the stock boost gauge which would suggest a bad map sensor. If this is showing on a mechanical gauge then I'm at a loss because once you let off the throttle the engine should immediately go into vacuum...

Re: "Barn" 1200 mile Royal Blue @ auction tomorrow http://www.autotrader.com/cars-for-sale/vehicledetails.xhtml?zip=46970&endYear=1993&modelCode1=TYPH&showcaseOwnerId=65143117&startYear=1990&makeCode1=GMC&searchRadius=0&mmt=%5BGMC%5BTYPH%5B%5D%5D%5B%5D%5D&listingId=351069651&Log=0 For sale again.

Re: #bigggun Put it to a vote.

Re: Borla exhaust, how loud are they? I have the borla cat back on my sy, very quiet and deep sound. I'll try to post a vid later today after work.

Re: Post a pic of your truck taken today That's views, replies 3800 ish. Best idea ever!

Re: frame The two holes in the bumper bracket means it has been replaced. Replacement brackets are bolt on instead of weld on, very common on these trucks because even a light hit will bend it.

Re: Autocross at Nats 2013 1. YES 2. YES 3. Don't care. 4. :dunno:

Re: Will this make me a bitch? As I see it, building an engine is just assembling parts. I realize there is a lot more to it than that; machining, blueprinting, balancing, etc. but my point is a monkey can be trained to use a torque wrench. I believe the real "work" in a build is in the...

Re: Post a pic of your truck taken today Glad you enjoy them!